Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: neptune bearing  (Read 3552 times)

Offline repairguy42

  • Technician
  • Member Since: Jan 2010
  • Posts: 52
neptune bearing
« on: August 30, 2010, 03:53:41 PM »

how long should it take to replace a rear bearing on a neptune washer?   is the bearing available by itself?   thanks for any help!

Offline applianceser

  • VIP Member
  • Member Since: May 2010
  • Posts: 11
Re: neptune bearing
« Reply #1 on: August 30, 2010, 07:11:21 PM »
How noisy is the bearing sound ???(like a jet plane taking off)??? if so it may take some work to remove the bearing from the outer tub(don't get MAD,take your TIME, or you can rent the "Tony-Tool" that does it quicker if you purchase the bearings from them,otherwise you can drive them out of the outer plastic drum with a pipe and nipple or large punch tool if your careful, but it can take 3 to4 hours depending how rusted the inner is plastic inside metal, replace both along with the lip-seal too, because if you don't you will do it again in the future and the bearings are relatively inexpensive (less than $25.00)the lip-seal gets a little pricey,but is manditory to save the inner bearing from water at about $30.00, again,well its apart do it ALL both bearings and seal and you should be good to go another 5+ years depending on your usage

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8809
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: neptune bearing
« Reply #2 on: August 30, 2010, 07:38:10 PM »
Is this a front loader or top loader?
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline RAH52

  • Technician
  • Member Since: Aug 2008
  • Posts: 961
  • Country: ca
Re: neptune bearing
« Reply #3 on: August 31, 2010, 05:49:59 AM »
personally I wouldn't bother much work vs. the life expectancy of washer


Neptune Bearing Repair - Pic Tutorial

Started by crystal368

Replies: 8
Views: 11958
Last post October 13, 2016, 11:57:05 AM
by soren4
Need a bearing kit for Neptune (and the puller)

Started by twmattox

Replies: 13
Views: 15438
Last post November 28, 2014, 01:36:03 PM
by fixitjeff
Maytag Neptune F/L Outer tub and bearing

Started by MajorApp

Replies: 3
Views: 5150
Last post February 06, 2010, 09:53:11 AM
by bobdell
Maytag Neptune MAH4000AWW Bearing Replacement (loud noise during spin)

Started by TonyWilliams

Replies: 6
Views: 20040
Last post December 11, 2011, 09:51:57 PM
by AJ
Maytag Neptune Bearing Replacement Project.

Started by schaffersapplian

Replies: 10
Views: 18096
Last post January 10, 2012, 10:20:09 AM
by JWWebster
Maytag Neptune Spin Problems after Bearing Replacement

Started by johnny_a

Replies: 8
Views: 10262
Last post April 02, 2013, 08:17:35 PM
by tgoods