Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: Need help with opening range top for gas stove to replace burner valve.  (Read 6491 times)

Offline bobafett13

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 1

Hello, I turned the knob to hard and it snapped the stem from the burner valve hence I need to replace the burner valve.  I believe this is the part I need:

However I am having trouble figuring out how to access the broken valve and more specifically what steps will be needed to taken afterwards.  I am not sure if I need to unscrew all of the sealed burner units or where the other screws are to open the top of the stove.

Model Number: GS465LEKS1 icon

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
« Last Edit: January 22, 2008, 12:46:13 PM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline rickgburton

  • Technician
  • Member Since: Oct 2007
  • Posts: 228
  • Country: us
  • Ricks Appliance Repair - 30 Years Experience
    • Buy me a beer through paypal
Re: Need help with opening range top for gas stove to replace burner valve.
« Reply #2 on: January 22, 2008, 01:51:18 PM »
In picture #2 you see the two screws holding the burner on, you'll have to remove all four burners and the top will come up and you can access the valve.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8809
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Need help with opening range top for gas stove to replace burner valve.
« Reply #3 on: January 24, 2008, 10:57:06 AM »
Don't try and raise the top with out removing those screws! You will break the aluminum lines on the front burners! OOPS! Those dang screws are hard to get out. some of them strip out or rust badly or have so much grease on them they just wont budge. Here is what I do in stubborn cases like that. I drill out the screws with a 1/8th inch bit. I replace the defective parts and When I put it back together I use 1/8th inch pop rivets to hold the burners back in place. this works well. O0
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL


Need to replace Burner Valve - GE Stove

Started by Bob1960

Replies: 9
Views: 11100
Last post March 14, 2011, 11:12:19 AM
by weverette
Gas stove using the 3.3 AMP draw opening valve

Started by domain

Replies: 7
Views: 1703
Last post February 13, 2015, 06:53:12 AM
by schleifha
Kenmore range 790.74003310 Oven clock resets everytime a stove burner sparks

Started by pkrepair

Replies: 1
Views: 683
Last post February 03, 2016, 06:50:28 PM
by dab147315
Whirlpool Range - Top Burner Not Working

Started by AJ

Replies: 0
Views: 7346
Last post December 28, 2007, 12:21:08 AM
by AJ
Kitchenaid Range LR Burner Inoperative

Started by TechnicianBrian

Replies: 0
Views: 3698
Last post April 17, 2008, 07:39:22 AM
by TechnicianBrian
ge center burner stove

Started by JPG

Replies: 4
Views: 6365
Last post May 23, 2008, 03:51:15 PM
by JWWebster