Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: Washer Walking on spin cycle  (Read 3054 times)

Offline Vernald

  • VIP Member
  • Member Since: May 2009
  • Posts: 1
Washer Walking on spin cycle
« on: May 19, 2009, 01:38:22 PM »

I have the same washer walking (off-balance) on spin cycle - Inglis Washer.  The tub (drum? basket?) and the agitator sits on off-center angle when empty.  I replaced the spring that holds the drum steady....adjusted the washer legs...just replaced the broken motor coupler....replaced the agitator gasket...what else to do?

Model FWS235RFS6
« Last Edit: May 19, 2009, 03:18:08 PM by Al Capone »

Offline Al Capone

  • Administrator
  • VIP Member
  • Member Since: Feb 2008
  • Posts: 409
  • Country: us
Re: Washer Walking on spin cycle
« Reply #1 on: May 19, 2009, 03:17:38 PM »

Please be sure to read, Posting Basics - Starting a New Topic.

Note were it say's towards the bottom.

Please do not ask your own question in a topic.
In other words, please don't hijack the topic and make it yours.
Start your own topic and reference the other topic related to your issue.

I have made your reply into a new topic. - Over 2 Million Appliance Parts In-Stock. 365-Day Hassle Free Return Policy!

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8809
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Washer Walking on spin cycle
« Reply #2 on: May 19, 2009, 08:43:53 PM »
you probably knocked it out of balance messing with that coupling.
Wiggle it around and run a few loads to get it back in sinc.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3023
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Washer Walking on spin cycle
« Reply #3 on: May 20, 2009, 06:07:35 AM »
Inglis is the Euro label for Whirlpool appliances, so this is the standard direct-drive washer. More than likely, if you laid it over during your coupler repair, the tub support or "skate plate" could have been bent or warped, or possibly the snubber pads that are mounted on it have become worn out.

Skate Plate Kit
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 369
  • Country: ca
Re: Washer Walking on spin cycle
« Reply #4 on: May 20, 2009, 08:38:07 AM »
I did one of these yesterday where the skate plate was broken in 2. The first time I've seen that!! I've also seen where they just get out of proper position and just need to be realigned without replacing.


Washer Walking on spin cycle

Started by Lee

Replies: 2
Views: 2614
Last post May 26, 2009, 11:09:26 AM
by Lee
washer shaking during the spin cycle and "Walking" during spin cycles also

Started by dnunley

Replies: 6
Views: 5198
Last post February 09, 2011, 06:43:50 AM
by jumptrout51
Maytag washer mah4000aww spin cycle

Started by evo100

Replies: 1
Views: 6688
Last post December 25, 2007, 09:41:02 PM
by AJ
washer works except spin cycle and has a burning rubber smell.

Started by hogslayer

Replies: 5
Views: 8707
Last post January 24, 2016, 07:12:08 PM
by ody
Maytag washer-- got agitation, no spin in spin cycle

Started by PB3

Replies: 13
Views: 23733
Last post March 28, 2008, 09:18:30 AM
by PB3
washer trips gfi at spin cycle

Started by rhartman93643

Replies: 7
Views: 7042
Last post April 18, 2008, 11:57:24 AM
by rhartman93643