Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: Maytag washer grinding/wire dragging on metal noise but inner tub won't come out  (Read 5864 times)

Offline markq

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 2

We bought the washer in 2000 and last week it began making a loud metal grinding noise that was evident primarily during spin but also does it during agitation, it's just not as obnoxious then since it's not being spun so fast. After reading other posts I figured out how to get to and remove the pump but it turns freely by hand with no noise and no visible obstructions. Turning the center pulley counter-clockwise (while looking up to the bottom of the washer) allows me to turn the transmission housing. Turning the center pulley the other direction it simply turns freely while the transmission housing refuses to turn. At this point I decided that I needed to remove the inner tub to continue troubleshooting. However, after removing the agitator and the 4 mounting screws I can not get the inner tub to come out. I've tried the stomping the side technique (hard), standing in the tub and stomping, banging on the tub and all other methods of trying to loosen it up but with no luck.
So, supposing I will need to remove the inner tub in order to either complete my troubleshooting or get to the part that may need replaced (or both?) what suggestions are there for doing this? I've read that the inner tub may sometimes become molded to some part of the assembly that it goes around and that it simply may not come out at all. If that's the case, what would a Maytag repairman do? Replace the tubs and transmission and all? Would Maytag offer some type of help? Given my situation, does it seem likely that a repair can be completed for substantially less than the $400 or so that a new one would cost?

Model MAV5000AWW

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3023
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Gottat love your many forums did you post this question on?

Here's the same answer I gave you on my board:

Your Atlantis needs a new tub bearing and seal kit. Not a job for you to tinker with, since special tools are required do the repair. You will likely be looking at a $300 repair, and no, Maytag will not be interested in helping you after 7 years.
The bearing and seal kit is pictured below, and although it is only a $55 part, the labor and service charges you incur to have it installed will cost you. It's either that or buy the spring, hub and seal tools just to do one job. Now, you're talking money 

« Last Edit: February 20, 2009, 03:02:15 AM by Repair-man »
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman

Offline markq

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 2
Thanks very much, Repair-man. Desperate folks sometimes do desperate things (especially late at night) and I decided to chase after the opinions of those who seemed to be the most knowledgeable.

I will now begin researching for a new, affordable, dependable machine. Surely, they're out there.

Thanks again.


Maytag LA8650 Washer - Grinding/Scraping/Rattle Noise During Spin Cycle

Started by Carol2

Replies: 17
Views: 18784
Last post April 02, 2009, 05:40:54 PM
by Carol2
Video: Maytag Washer Making Tick Tock Noise

Started by AJ

Replies: 2
Views: 5867
Last post December 07, 2007, 05:41:44 PM
by AJ
Maytag washer noise during high speed spin

Started by madbchron

Replies: 2
Views: 6017
Last post February 05, 2008, 10:03:59 AM
by JWWebster
Maytag washer spin noise

Started by idler

Replies: 10
Views: 11874
Last post January 07, 2011, 04:09:52 PM
by Repair-man
Kenmore Washer Makes Grinding Noise and does nothing

Started by Jaytag

Replies: 3
Views: 5299
Last post January 07, 2010, 11:26:00 AM
by JWWebster
Maytag Front Load Neptune Washer Banging Noise when Spinning

Started by dkmminc

Replies: 11
Views: 22963
Last post June 17, 2010, 11:05:11 PM
by schaffersapplian