Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: Dacor Range F1 Error Code  (Read 33431 times)

Offline TechnicianBrian

  • Technician
  • Member Since: Dec 2007
  • Posts: 390
  • Country: us
Dacor Range F1 Error Code
« on: November 09, 2008, 07:34:10 AM »

Model #ERD30S06BR, this dual fuel range would display an F1 error code at what seemed to be completely random times. Each time the error occurred, it could be cleared by pressing the cancel button only to have the error message reappear moments or even hours later. The only thing that would keep the error at bay was shutting off the power at the circuit breaker. With this error coming and going, the oven became all but unusable to the customer.

The F1 error is, as Dacor describes it, a system watchdog circuit used to monitor the bake element relays for a possible failure such as a command to supply heat without receiving an input from the switch membrane. These element relays which are mounted on the ovens relay board turn the L1 and L2 line voltages on and off to the bake element. If either of these relays were to actuate without a key press, the watchdog should catch the operation and display an F1 error.

Once the error has been displayed, it is cleared with the cancel button, and should no longer occur, but if it does, the recommended repair is to check the ovens main control and replace as needed. Because this error was reoccurring, the control board was the likely candidate for replacement, but the completely intermittent timing of the error seemed to indicate something else in this range was amiss. Looking at the wiring diagram for other components which may be at fault lead me to the front of the range, and the item that was the real reason for these random errors.

The door latch mechanism is used during the self clean cycle to ensure the door remains closed and locked until complete. The latch contains two micro switches used to monitor the position of the latch motor allowing the control board to know the position of the door and latch. What was discovered (I had the assistance of one of my students) is one of the switches had been shorting to the frame due to an excess buildup of grease and grime from years of use. This short circuit was being interpreted by the main control as a problem, thus the reason for the F1 error.

A new latchicon assembly complete with two micro switches and motor was installed into this range allowing the oven to once again turn on and off when needed. The unit functions as expected once again, and the error message has gone away for good.

Offline Dacorneveragain

  • VIP Member
  • Member Since: May 2016
  • Posts: 1
Re: Dacor Range F1 Error Code
« Reply #1 on: May 22, 2016, 07:57:25 PM »
Thanks I Scrubbed the door latch mechanism and two black temperature sensors with red reset buttons on top lightly with toothbrush and vacuumed and thus fixed it,   both were covered with dust bunnies and shorting sensors especially during humid weather


Whirlpool Polara Range Error Code

Started by TechnicianBrian

Replies: 5
Views: 13711
Last post December 29, 2008, 09:03:25 PM
by TechnicianBrian
Frigidaire gas range error code F10

Started by max190

Replies: 4
Views: 17823
Last post February 06, 2009, 02:52:59 PM
by max190
F9 error code on maytag5780 gas range

Started by kdmurphy44

Replies: 1
Views: 4124
Last post February 07, 2009, 08:48:53 PM
by Repair-man
Kenmore range shows f15 error code

Started by desertfox

Replies: 13
Views: 18506
Last post November 03, 2010, 11:33:09 AM
by prime311
F10 error code on a Frigidaire gas range

Started by jasunderland

Replies: 3
Views: 6988
Last post April 27, 2011, 10:48:15 PM
by JWWebster
Kenmore Electric range model# 790.99013100 F7 Error code

Started by Washaman

Replies: 1
Views: 3762
Last post August 11, 2013, 11:14:40 AM
by haroldsappliance