Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: Kenmore Dishwasher  (Read 5273 times)

Offline stljrs

  • VIP Member
  • Member Since: Sep 2008
  • Posts: 6
Kenmore Dishwasher
« on: September 18, 2008, 09:52:42 AM »

Hi folks,

Is this the procedure I need to use to replace my pump/sump assembly?  Kenmore model is 665.17469300.;sa=view;down=233

Is there basically just one part for all whirlpool/kenmore dishwashers that have this set up?  Could someone give me the whirlpool part number?  I may try to change ours out.  It's starting to get noisy and since the it seems to be mostly plastic, everything is probably getting worn on it and could use replacing.  I've seen several very similar assemblies (if I have the correct one) on the internet for $175 - $200 and this basically would give us a new washer.  Much cheaper than springing for a new one that is comparably quiet.

Thank you.

Model 665.17469300

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kenmore Dishwasher
« Reply #1 on: September 18, 2008, 10:27:47 AM »

 # 15 in PUMP AND MOTOR Diagram

 old part # 8268422
new part # 8535150
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline stljrs

  • VIP Member
  • Member Since: Sep 2008
  • Posts: 6
Re: Kenmore Dishwasher
« Reply #2 on: September 18, 2008, 11:20:53 AM »
Thank you.

Offline stljrs

  • VIP Member
  • Member Since: Sep 2008
  • Posts: 6
Re: Kenmore Dishwasher
« Reply #3 on: October 02, 2008, 02:59:15 PM »
Just as a follow-up.  The dishwasher shot craps.  Knowing I could get help on the forum gave me the guts to try the repair myself.  I pulled the kick panel off and decided I was best served unhooking it and putting it up on its back so I could clearly see what I was doing.  I'm not sure I would have been successful had I not have.  Including pulling the DW out and hooking it back up, the whole job took 2 1/2 hours.  I was very meticulous and took pics of wiring just to be safe.  I didn't install it so I was learning as I went there also.

It now sounds and runs like new and (crossing fingers) I have no leaks.




Kenmore Dishwasher - Doesn't always drain.

Started by yeltu1188

Replies: 1
Views: 7406
Last post September 15, 2007, 10:36:53 AM
by Pegi
Kenmore Elite Dishwasher

Started by sparky823

Replies: 8
Views: 10480
Last post October 11, 2007, 09:16:14 AM
by Pegi
Kenmore Elite Dishwasher Does Not Start

Started by rgletter

Replies: 5
Views: 9349
Last post December 14, 2007, 07:45:52 PM
by rickgburton
Kenmore 665 dishwasher chopper assembly cover

Started by tomnewf

Replies: 2
Views: 11763
Last post January 06, 2008, 10:59:43 AM
by AJ
Kenmore dishwasher

Started by lcsw

Replies: 4
Views: 7950
Last post February 08, 2008, 05:04:28 PM
by AJ
Kenmore dishwasher motor problem

Started by lgmccoy1

Replies: 3
Views: 12026
Last post February 22, 2008, 11:06:24 AM
by RegUS_PatOff