Get Answers to your Appliance Repair Questions

Washer Parts  ·   Dryer Parts  ·   Refrigerator Parts  ·   Dishwasher Parts  ·   Range/Cooktop/Oven Parts  ·   All Appliance Parts 

Author Topic: Maytag Dependable Drive Washer - Leaks Water  (Read 9358 times)

Offline AJ

  • Technician
  • Member Since: Jun 2007
  • Posts: 10865
  • Country: us
    • - Appliance Repair
Maytag Dependable Drive Washer - Leaks Water
« on: May 29, 2008, 07:10:20 PM »

Complaint: Washer leaks water.

As I started the washer so it would fill with water as I removed the font panel.
Once I had the front panel removed it was easy to see were the water leak was.

The water was leaking out the bottom of the tub were the transmission goes through to the agitator.

Solution: Install the Mounting Stem and Boot Seal Kit icon

The hardest part of this job is often getting the old parts out. It helps to have the right tools and one tool you need for this job is the maytag Spanner Wrench icon

It also helps to remember that the parts have left handed threads on them.

Even with the right wrench and the knowledge of the left handed threads you still may need to cut the old part off to get it removed.

A dremel with a reinforced cutting wheel makes this a easy task.

With a little knowledge, the correct tools and little time you can have your maytag washer up and running like new again too.

There are 27 photos related to this repair in our Photo Gallery.

Model LAT9706AAE
« Last Edit: May 29, 2008, 09:02:28 PM by AJ »

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3023
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Maytag Dependable Drive Washer - Leaks Water
« Reply #1 on: May 30, 2008, 05:41:48 AM »
As a further note, if you see any rust whatsoever under the boot seal when you have it apart like that last photo shows, replace the tub bearing as well. If you do not, the boot seal will fail again in short order plus the tub willl not spin well.

Parts used in this repair are the 22204012 boot stem kit and the 204013 bearing assy. Always add 5 drops of Zoom Oil to the bearing after it is installed and the lower boot is in place. (Keep the oil away from the seal surface.)
« Last Edit: May 30, 2008, 06:47:11 AM by Repair-man »
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman


Maytag dependable care washer sticky drive pulley

Started by kevster

Replies: 4
Views: 5559
Last post July 10, 2011, 09:34:19 PM
by AJ
Maytag Washer LAT9704AAE leaks water.

Started by AJ

Replies: 3
Views: 3038
Last post December 29, 2011, 02:24:52 PM
by bigbuck
Video: How To Replace a Water Pump On A Whirlpool Made Direct Drive Washer

Started by AJ

Replies: 0
Views: 12630
Last post August 10, 2007, 08:42:54 PM
by AJ
How to replace a Maytag - Amana washer water pump and belt.

Started by AJ

Replies: 19
Views: 45879
Last post September 23, 2016, 04:37:22 PM
by gselvo
Video: Replace Belts on Maytag Dependable Care Washer

Started by AJ

Replies: 2
Views: 12499
Last post November 20, 2007, 07:44:07 PM
by AJ
Maytag Ensignia washer won't extract water

Started by nandomay

Replies: 1
Views: 5310
Last post December 30, 2007, 11:53:58 AM
by TechnicianBrian