Author Topic: PAV3240AWW Maytag washer  (Read 2094 times)

Offline wildimaginations

  • Technician
  • Member Since: Jul 2011
  • Posts: 621
  • Country: us
PAV3240AWW Maytag washer
« on: April 10, 2012, 01:11:50 PM »
Is there a video on how to repair the brake assembly on this Maytag washer?  Not just remove but actually get into the guts of this thing to replace the parts.


Thanks




Appliance Service Technician
Authorized servicer on LG appliances.
About 45 mins east of San Francisco

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: PAV3240AWW Maytag washer
« Reply #1 on: April 10, 2012, 08:46:30 PM »
only breakdown i could find was from jw blog, see if this will help ya:
http://foggyfacts.blogspot.com/2011/03/single-belt-maytag-washer-de-mystified.html

Offline wildimaginations

  • Technician
  • Member Since: Jul 2011
  • Posts: 621
  • Country: us
Re: PAV3240AWW Maytag washer
« Reply #2 on: April 10, 2012, 10:29:06 PM »
Is there a special tool to remove the plate where the spring sit inside of?  Or can I just remove all 6 screws and it won't fly off?  I've never done one of these so I'm curious.
Appliance Service Technician
Authorized servicer on LG appliances.
About 45 mins east of San Francisco

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: PAV3240AWW Maytag washer
« Reply #3 on: April 10, 2012, 10:53:59 PM »
I have the tool. After removing the main pulley you slide this dude up on the shaft and it has a nice carter pin that shoves into a couple holes in the tool. The carter pin goes into a grove cut into the transmission shaft. The tool features a threaded shaft  and a nut along with a few washers. After securing the rig to the shaft, you tighten the nut, and that causes  the spring to get compressed inside the brake package. You know you are far enough when the whole shebang turns freely. You then remove the screws and back slowly off the shaft till the bottom plate and the spring comes off.
« Last Edit: April 10, 2012, 11:12:02 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline tgoods

  • Technician
    Moderator
  • Member Since: Jul 2010
  • Posts: 1527
  • Country: us
    • Buy me a beer through paypal
Re: PAV3240AWW Maytag washer
« Reply #4 on: April 10, 2012, 11:32:24 PM »
The brake tool, 12002012, is NLA.  If you remove the screws you may die or lose a limb.  I've heard of people replacing the screws, one at a time, with longer screws.  Then backing them out a little at a time until the spring tension is released.  You can borrow my brake tool, but I will need a $300 deposit and you pay shipping both ways. :)

Offline wildimaginations

  • Technician
  • Member Since: Jul 2011
  • Posts: 621
  • Country: us
Re: PAV3240AWW Maytag washer
« Reply #5 on: April 11, 2012, 04:44:46 AM »
Thanks but I don't think the customer wants it done.  Will probably end up replacing the whole unit.
Appliance Service Technician
Authorized servicer on LG appliances.
About 45 mins east of San Francisco

Offline dab147315

  • Technician
  • Member Since: Oct 2010
  • Posts: 1662
  • Country: us
Re: PAV3240AWW Maytag washer
« Reply #6 on: April 14, 2012, 05:44:33 PM »
1st source servall has them in stock. PART 12002012 tool.
.

Offline theoldstoveguy

  • Technician
  • Member Since: Jan 2008
  • Posts: 1353
  • Country: us
    • Buy me a beer through paypal
Re: PAV3240AWW Maytag washer
« Reply #7 on: April 14, 2012, 06:58:58 PM »
Says discontinued.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: PAV3240AWW Maytag washer
« Reply #8 on: April 14, 2012, 07:22:09 PM »
You can make a tool. All you need is a little 1 inch all thread about a foot long. A piece of thread pipe 3 inchs long with 2 holes drilled in it, a few washers, a nut, and a u-bolt.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline dab147315

  • Technician
  • Member Since: Oct 2010
  • Posts: 1662
  • Country: us
Re: PAV3240AWW Maytag washer
« Reply #9 on: April 14, 2012, 08:16:40 PM »
On 1st source web site now 14 in Detroit and 7 in Houston$59.80 cost# 12002012 part.

 

Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 9305
Last post February 09, 2013, 07:41:01 AM
by def
Video: Old Maytag Gas Washer

Started by AJ

Replies: 2
Views: 4261
Last post September 04, 2007, 10:34:57 PM
by AJ
Maytag Washer Bearing Repalcement MLG2000AWW

Started by davidpgh1

Replies: 8
Views: 11059
Last post January 06, 2008, 01:59:10 PM
by inot66
Maytag LAT8704AAE Washer Leak

Started by endresrk

Replies: 3
Views: 5859
Last post August 28, 2007, 08:11:12 PM
by AJ
How to replace a Maytag - Amana washer water pump and belt.

Started by AJ

Replies: 18
Views: 31280
Last post April 19, 2010, 08:23:29 PM
by JWWebster
How old is my Maytag washer?

Started by jon

Replies: 1
Views: 18595
Last post September 03, 2007, 12:42:08 PM
by AJ