Author Topic: Kenmore 110.67732791 heating element stays on  (Read 2936 times)

Offline bladeguy08

  • VIP Member
  • Member Since: Dec 2008
  • Posts: 9
Kenmore 110.67732791 heating element stays on
« on: February 06, 2012, 03:28:53 PM »
When I open the door and the dryer stops turning heating element stays on. From researching other posts, it seems like I need another heating element. This dryer is approx 16 years old and I have replaced the heating element, rollers and belt once. I'm trying to decide if I should repair it again or purchase a new/reconditioned one from a sears outlet center. We are a family of 5 and the dryer gets used heavily.


Model 110.67732791

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #1 on: February 06, 2012, 03:44:22 PM »
The heating element is probably broken and shorted to ground inside the canister.
If the dryer is working fine otherwise you should just get a new element.
Take a Kid fishing.

Offline bladeguy08

  • VIP Member
  • Member Since: Dec 2008
  • Posts: 9
Re: Kenmore 110.67732791 heating element stays on
« Reply #2 on: February 06, 2012, 06:01:13 PM »
After posting, I figured I'd put a limit on this repair at $100. Anything over and I may think about a new dryer. With that said I pulled out the heating element to see if it was broken. I tested it for continuity and it is good. I also tested the high limit switch and it also was good. Not sure what to check next.

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #3 on: February 06, 2012, 06:18:52 PM »
relay? test terminal to ground on element with meter?
« Last Edit: February 06, 2012, 06:22:54 PM by bigbuck »

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #4 on: February 06, 2012, 06:39:16 PM »
usally those clam shell heater short out to ground @ the top right hand side, where the element bends to the other side, if you bend element off bracket, you may get a year or two, re-installing back in. i have done it. O0
 
 
note: element will show good, due to shorted to ground but, not broken!
« Last Edit: February 06, 2012, 06:41:26 PM by bigbuck »

Offline bladeguy08

  • VIP Member
  • Member Since: Dec 2008
  • Posts: 9
Re: Kenmore 110.67732791 heating element stays on
« Reply #5 on: February 06, 2012, 06:42:38 PM »
That's exactly what it is. The coil is touching the metal plate. Hopefully that was the only problem. I will reassemble it and see.

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #6 on: February 06, 2012, 06:44:48 PM »
 O0 , make sure you bend it enough where it will not extract with heat, & ground out again!

Offline bladeguy08

  • VIP Member
  • Member Since: Dec 2008
  • Posts: 9
Re: Kenmore 110.67732791 heating element stays on
« Reply #7 on: February 06, 2012, 07:41:57 PM »
Reassembled it and it seems to be working. Thanks for the help.

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #8 on: February 06, 2012, 07:47:02 PM »
your welcome, glad i could help! ;)

Offline AnnesLimo

  • VIP Member
  • Member Since: Feb 2012
  • Posts: 31
Re: Kenmore 110.67732791 heating element stays on
« Reply #9 on: February 15, 2012, 05:15:32 PM »
Got a similar problem here except I just installed a new element and have looked, tested and inspected all wires / connections for shorts to no avail. Dryer runs fine but heating element will not turn off if door opened or timer is in any position other than off or air dry? Is it possible to be the timer control unit? I did have a mishap with a short out when I forgot to unplug the unit before disconecting the feed to the high limit thermo whcih I also replaced as well as 250 the thermo?

Also on another note the motor temp breaker keeps kicking out shutting down the cycle. I have cleaned all the rollers and everything else as well but I suspect this may be related to the heater element staying on and overheating the cabinet interior space?

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #10 on: February 15, 2012, 05:22:10 PM »
can you recheck that model number. thanks

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: Kenmore 110.67732791 heating element stays on
« Reply #11 on: February 15, 2012, 06:22:03 PM »
Got a similar problem here except I just installed a new element and have looked, tested and inspected all wires / connections for shorts to no avail. Dryer runs fine but heating element will not turn off if door opened or timer is in any position other than off or air dry? Is it possible to be the timer control unit? I did have a mishap with a short out when I forgot to unplug the unit before disconecting the feed to the high limit thermo whcih I also replaced as well as 250 the thermo?

Also on another note the motor temp breaker keeps kicking out shutting down the cycle. I have cleaned all the rollers and everything else as well but I suspect this may be related to the heater element staying on and overheating the cabinet interior space?
You need to start a new topic with this problem.
Take a Kid fishing.

Offline AnnesLimo

  • VIP Member
  • Member Since: Feb 2012
  • Posts: 31
Re: Kenmore 110.67732791 heating element stays on
« Reply #12 on: February 15, 2012, 07:00:16 PM »
I could but it's the same problem that needs a different solution?

Offline Earl Dryer

  • Technician
  • Member Since: May 2008
  • Posts: 166
  • Country: us
Re: Kenmore 110.67732791 heating element stays on
« Reply #13 on: February 15, 2012, 07:04:00 PM »
Just because the element is new doesn't make it good. Take it off and check for a broken insulator, it has happened to me on couple occasions.

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9390
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Kenmore 110.67732791 heating element stays on
« Reply #14 on: February 15, 2012, 07:06:04 PM »

I could but it's the same problem that needs a different solution?


Please do start a new topic and if you feel this topic is related to your problem post a link to it from your topic.


This topic belongs to someone else.


If we just had one topic for every dryer that did not heat or every refrigerator that did not cool things would get very confusing around here.


Thanks for understanding.
Hope you find our site helpful.

 

Kenmore 90 series heating element stays on.

Started by AnnesLimo

Replies: 63
Views: 7612
Last post February 18, 2012, 09:42:43 PM
by tgoods
Lady Kenmore portable 110V clothes dryer heating element does not turn off

Started by mizzn1t

Replies: 1
Views: 3779
Last post November 26, 2008, 07:43:07 PM
by JWWebster
Replacing the Heating Element on a Kenmore Serise 70 Electric Dryer

Started by jracmm

Replies: 1
Views: 2255
Last post December 02, 2008, 07:34:16 PM
by JWWebster
Kenmore Model 70 electric dryer heating element 279838

Started by kjb

Replies: 1
Views: 4993
Last post April 24, 2010, 12:47:40 PM
by JWWebster
Kenmore series 90 heating coil stays on when door is open

Started by RT1976

Replies: 20
Views: 5330
Last post September 09, 2011, 04:18:14 PM
by JWWebster
heating element

Started by brad

Replies: 5
Views: 4506
Last post February 15, 2008, 03:47:18 PM
by brad