Author Topic: Maytag Washer Won't Start  (Read 1351 times)

Offline app1

  • Technician
  • Member Since: Aug 2011
  • Posts: 186
Maytag Washer Won't Start
« on: January 22, 2012, 12:10:18 PM »
I have a Maytag Washer Model # MHWZ600TB01 and when you power it up everything lights up ok BUT it will only go through the Spin Only cycle, EVERY other option like Normal or Hand Wash when you hit the Start button the machine shuts shuts off. When I checked for error codes I found an F24 that says something about a water temp sensor but I was told that this must be an old code as NO error codes come up it just shuts off!! CCU,MCU problem maybe? When I do the hit the same button for 4 sec the pause then again is when the F24 shows up. Then I press the same button again and it starts at I believe sanitize or something with a 4 then it moves up to the next cycle and displays 11 then from there it just shuts down again, is this the diagnostics test that it is shutting down during? and if it is what does this point to. VERY CONFUSED - PLEASE HELP - ANY IDEAS OR SUGGESTIONS WOULD BE APPRECIATED!! THANKS IN ADVANCE FOR ANYONES HELP!!



Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Maytag Washer Won't Start
« Reply #1 on: January 22, 2012, 12:49:19 PM »
Number 24 is the temp sensor

WHIRLPOOL Water Temperature Switch, part number: AP3128829


May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline app1

  • Technician
  • Member Since: Aug 2011
  • Posts: 186
Re: Maytag Washer Won't Start
« Reply #2 on: January 22, 2012, 02:36:09 PM »
I will try this, I am just confused as to why I do not get the 24 code / It just shuts down except when I press Spin Only -

Offline app1

  • Technician
  • Member Since: Aug 2011
  • Posts: 186
Re: Maytag Washer Won't Start
« Reply #3 on: January 22, 2012, 02:40:05 PM »
Can I replace this easily? From the back near the heater element?

Offline LowSL2

  • Technician
  • Member Since: Dec 2011
  • Posts: 838
  • Country: us
  • Fletch F. Fletch
    • Buy me a beer through paypal
Re: Maytag Washer Won't Start
« Reply #4 on: January 22, 2012, 03:41:07 PM »
It's most likely a broken wire to the temp sensor in the back. If the wires are good and have near zero ohms resistance back to the CCU, the sensor needs replacement. It will spin if the sensor is bad. It wont star a wash cycle.
LowSL2
15 Years of Professional Appliance Repair Experience

 

help with maytag neptune front load washer start but stop after few seconds..

Started by soccerboy

Replies: 4
Views: 5648
Last post August 06, 2008, 06:40:10 AM
by Repair-man
Maytag Washer wiring from motor to start switch

Started by techman51

Replies: 7
Views: 6025
Last post April 23, 2009, 05:52:54 PM
by stu3430
Maytag washer won't start or fill

Started by klb3780

Replies: 1
Views: 3496
Last post January 07, 2010, 09:47:54 PM
by AJ
Maytag washer model LAT3500AAE fills w/water,shuts off, won't start again

Started by 3rdwasherfromcl

Replies: 5
Views: 1384
Last post June 16, 2013, 08:28:09 PM
by 3rdwasherfromcl
Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 8323
Last post February 09, 2013, 07:41:01 AM
by def
Video: Old Maytag Gas Washer

Started by AJ

Replies: 2
Views: 3894
Last post September 04, 2007, 10:34:57 PM
by AJ