Author Topic: Maytag Neptune TL stuck on agitate  (Read 1439 times)

Offline Blaiser

  • Technician
  • Member Since: Jun 2011
  • Posts: 222
  • Country: us
    • Buy me a beer through paypal
Maytag Neptune TL stuck on agitate
« on: January 08, 2012, 08:38:33 AM »
Maytag Neptune TL - Model# FAV6800AWW is stuck on agitate at the 30 minute mark displayed on the LED and will not advance. The machine just spins and will not advance to the next cycle. Regardless if I cancel the cycle or not, I tried unplugging the machine and resetting the cycle but it just wants to agitate. Tried getting into the diagnostics and the low water level code showed that the machine was low on water. Took the pump out and did find a couple coins thinking this would be the issue but still not advancing. Machine will not pump out unless I go into diagnostics and force the pump to come on. Now the machine will not fill it just sits there and agitates.  Would the motor control board need replacing or Main control board? Any sugguestions?

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: Maytag Neptune TL stuck on agitate
« Reply #1 on: January 08, 2012, 09:33:24 AM »
sounds like the main control, but an these machines i have replaced the clutch alot.

Offline LowSL2

  • Technician
  • Member Since: Dec 2011
  • Posts: 853
  • Country: us
  • Fletch F. Fletch
    • Buy me a beer through paypal
Re: Maytag Neptune TL stuck on agitate
« Reply #2 on: January 09, 2012, 12:38:23 AM »
The drain pump wont turn on until the control board senses the basket is spinning at 90 RPM or higher.  It could be the clutch or the tub displacement sensor.  My money is on a bad clutch.
LowSL2
15 Years of Professional Appliance Repair Experience

Offline Blaiser

  • Technician
  • Member Since: Jun 2011
  • Posts: 222
  • Country: us
    • Buy me a beer through paypal
Re: Maytag Neptune TL stuck on agitate
« Reply #3 on: January 28, 2012, 09:29:44 PM »
Ok got into the Maytag Neptune TL today. I replaced the Clutch. While I was under there I also replaced the Tub Seal and both the inner and outer bearings #6207DU. While removing the tub I found $3.32 in quarters, dimes, nickels and pennies under the left paddle. I was hoping this would cause the washer to stall but after buttoning up everything I tried a quick wash which started at 30 MINUTES and it filled and agitated till it got to 24 minutes and just sat there and agitated still? Any help would be appreciated. I do not know what else to do.....



WHIRLPOOL Clutch Assembly Part # 25001169



Whirlpool Tub Seal Part # 25001090

Offline Blaiser

  • Technician
  • Member Since: Jun 2011
  • Posts: 222
  • Country: us
    • Buy me a beer through paypal
Re: Maytag Neptune TL stuck on agitate
« Reply #4 on: January 28, 2012, 09:31:02 PM »
(2) Bearings needed are the same 6207DU Inner and Outer

 

Maytag Performa Washer won't agitate - think it's stuck transmission

Started by staggerlee

Replies: 1
Views: 4730
Last post July 28, 2011, 10:58:48 PM
by JWWebster
Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 8550
Last post February 09, 2013, 07:41:01 AM
by def
Maytag Neptune MAH4000AWW - No Spin.

Started by larry

Replies: 39
Views: 61260
Last post February 21, 2011, 01:22:14 PM
by bwhelan
Maytag Dep. Care No Agitate

Started by CHolleman

Replies: 9
Views: 5419
Last post September 24, 2007, 12:31:49 PM
by AJ
Maytag Neptune MAH3000AWW Serial 19103060UB

Started by LarryC

Replies: 9
Views: 7985
Last post September 29, 2007, 09:49:12 PM
by AJ
Maytag Neptune MAH4000AWW Won't Drain Water / Smell

Started by mightymac

Replies: 22
Views: 24915
Last post February 15, 2013, 04:35:03 PM
by def