Author Topic: Hotpoint Range / Stove / Oven Fault Codes  (Read 2688 times)

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9390
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Hotpoint Range / Stove / Oven Fault Codes
« on: December 15, 2011, 12:40:42 PM »

 
Failure Code
Fault Code Description
Solution
F0
Stuck touch pad
Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.
F1
Stuck touch pad
Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both. Refer to F1 test at the top of this page for more information.
F2
 During
 BAKE
Control senses oven temperature above 615F-630F
If actual over temperature condition occurred: Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC).
 
 If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.
 
 Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature.
F2
 During
 CLEAN
Control senses oven temperature above 915F-930F
If actual over temperature condition occurred: Look for welded relay contacts. If this happens, replace oven control (also called clock or ERC).
 
 If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective. Check door lock switches.
 
 Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature.
F3
 or
 F4
Open or shorted oven temperature sensor (RTD)
Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.
F7
Stuck touch pad or bad clock
Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.
F9
Lock switch
Check wiring to door lock switch (the wire harness may be connected wrong). Check for stuck lock switch.
 

Find Parts
Fault Code Index
Hope you find our site helpful.

 

Maytag Range / Stove / Oven Fault Codes

Started by AJ

Replies: 0
Views: 4742
Last post December 15, 2011, 11:35:14 AM
by AJ
Whirlpool Range / Stove / Oven Fault Codes

Started by AJ

Replies: 0
Views: 3677
Last post December 15, 2011, 11:49:09 AM
by AJ
Frigidaire Range / Stove / Oven Fault Codes

Started by AJ

Replies: 0
Views: 8882
Last post December 15, 2011, 12:30:40 PM
by AJ
GE Range / Stove / Oven Fault Codes

Started by AJ

Replies: 0
Views: 3820
Last post December 15, 2011, 12:32:15 PM
by AJ
Admiral Range / Stove / Oven Fault Codes

Started by AJ

Replies: 0
Views: 2771
Last post December 15, 2011, 12:36:29 PM
by AJ
Dacor Range / Stove / Oven Fault Codes

Started by AJ

Replies: 0
Views: 2471
Last post December 15, 2011, 12:37:45 PM
by AJ