Author Topic: Maytag LAT5005AAE washer  (Read 2659 times)

Offline diverboy1980

  • Technician
  • Member Since: Nov 2011
  • Posts: 70
Maytag LAT5005AAE washer
« on: November 28, 2011, 08:48:46 PM »
I am working on this 1995 model Maytag washer. It will not agitate or spin. It was supposedly agitating but not spinning or draining for a week or so but now it also will not agitate. All it will do is fill with water. No humming or any other noises from the motor and the motor is cool to the touch. Unhooked the wires from the motor blue, white, yellow, red, and black. Black measures 120 VAC with timer in spin position and no power on any other wire. With all this wires hooked to the motor I read 120 VAC on all of them.


Bad motor? part # 12002351


Model LAT5005AAE

Offline whirlpooltech

  • Technician
  • Member Since: Nov 2007
  • Posts: 1367
  • Country: us
  • 20 years of experience
Re: Maytag LAT5005AAE washer
« Reply #1 on: November 28, 2011, 08:58:04 PM »
Did you take a look at the Lid Switch & Fuse, part # 22001682

Offline diverboy1980

  • Technician
  • Member Since: Nov 2011
  • Posts: 70
Re: Maytag LAT5005AAE washer
« Reply #2 on: November 28, 2011, 09:28:52 PM »
The fuse was fine, no power on the brown wire on one side of it or the white wire on the other side. Black switch had power on both sides. White switch had power on red and on black but no power on white which was the middle wire. I am not very familiar with these types of lid switches. Just from the information I told you I thought the lid switch was ok so I went down to the motor and started testing. If I am overlooking something please tell me.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Maytag LAT5005AAE washer
« Reply #3 on: November 28, 2011, 10:00:40 PM »
That white switch is known as the lid check switch, part # 207166
Remove it and examine the red button on it. It should be spring loaded and you should hear an audible click when you push the button. If the fuse is blown the washer won't fill, if it won't agitate then that small micro check switch is the usual suspect on that washer. Very common failure on these washers.
« Last Edit: November 28, 2011, 10:06:01 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline diverboy1980

  • Technician
  • Member Since: Nov 2011
  • Posts: 70
Re: Maytag LAT5005AAE washer
« Reply #4 on: November 28, 2011, 10:02:52 PM »
Looking at diagrams it appears I should be getting power from the yellow wire off the check switch down to the yellow wire on the motor. Does this sound correct?

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Maytag LAT5005AAE washer
« Reply #5 on: November 28, 2011, 10:07:49 PM »
Sometime mechanically the whole lid switch assembly is wankers but mostly it is the check switch if it fills but won't wash.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline diverboy1980

  • Technician
  • Member Since: Nov 2011
  • Posts: 70
Re: Maytag LAT5005AAE washer
« Reply #6 on: November 28, 2011, 10:40:55 PM »
For testing I have a check switch I will try and if that works I will replace the entire assembly. I will ohm it out first just to see if it is working properly when opening and closing the lid.

Offline whirlpooltech

  • Technician
  • Member Since: Nov 2007
  • Posts: 1367
  • Country: us
  • 20 years of experience
Re: Maytag LAT5005AAE washer
« Reply #7 on: November 28, 2011, 10:51:07 PM »
Sometimes the entire switch assembly needs to be adjusted a little bit if it's slid out of place.
I see far more problems with this type of lid switch then with the motors.


Offline diverboy1980

  • Technician
  • Member Since: Nov 2011
  • Posts: 70
Re: Maytag LAT5005AAE washer
« Reply #8 on: November 29, 2011, 07:06:18 AM »
I am going to check it out again this evening and verify the two switches are ok on the lid switch assembly. I was still curious if the black wire at the motor is the only one I should read 120 or if I should be getting the reading on other wires.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Maytag LAT5005AAE washer
« Reply #9 on: November 30, 2011, 05:18:28 AM »
... With all this wires hooked to the motor I read 120 VAC on all of them.
bad Timer
Red Wire should be 0v

Maytag Washer Timer, part # 22001530
 
« Last Edit: November 30, 2011, 05:21:23 AM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

 

Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 9309
Last post February 09, 2013, 07:41:01 AM
by def
Video: Old Maytag Gas Washer

Started by AJ

Replies: 2
Views: 4262
Last post September 04, 2007, 10:34:57 PM
by AJ
Maytag Washer Bearing Repalcement MLG2000AWW

Started by davidpgh1

Replies: 8
Views: 11063
Last post January 06, 2008, 01:59:10 PM
by inot66
Maytag LAT8704AAE Washer Leak

Started by endresrk

Replies: 3
Views: 5860
Last post August 28, 2007, 08:11:12 PM
by AJ
How to replace a Maytag - Amana washer water pump and belt.

Started by AJ

Replies: 18
Views: 31285
Last post April 19, 2010, 08:23:29 PM
by JWWebster
How old is my Maytag washer?

Started by jon

Replies: 1
Views: 18601
Last post September 03, 2007, 12:42:08 PM
by AJ