Author Topic: Maytag MEDB800VQ0 Belt  (Read 1254 times)

Offline azjsmith

  • VIP Member
  • Member Since: Nov 2011
  • Posts: 1
Maytag MEDB800VQ0 Belt
« on: November 05, 2011, 01:52:24 PM »
My belt and Pulley Nut came off my dryer.  Going though the back of the machine, I screwed the nut back down but the belt is too tight to get back on.  I obtained a copy of the service manual however that just shows replacement parts.  Its a tight area to work.  can anyone recommend suggestions on ow to get this belt back on?  Thank you!



Model MEDB800VQ0

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Maytag MEDB800VQ0 Belt
« Reply #1 on: November 05, 2011, 02:10:32 PM »
You gotta go through the front. Pop the top with a putty knife. Then remove the front then shroud. Then get the drum out and clean her up. Their are 2 belts on this one. It is a crappy design. The lint tends to pool up very badly in the blower and filter area.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline MajorApp

  • Technician
  • Member Since: Feb 2008
  • Posts: 550
  • Country: us
Re: Maytag MEDB800VQ0 Belt
« Reply #2 on: November 05, 2011, 11:37:21 PM »
Tell me about it.

Online tgoods

  • Technician
    Moderator
  • Member Since: Jul 2010
  • Posts: 1496
  • Country: us
    • Buy me a beer through paypal
Re: Maytag MEDB800VQ0 Belt
« Reply #3 on: November 06, 2011, 09:14:35 AM »
You need to apply thread lock to the threads of the blower shaft.  Route the belt so it doesn't interfere with the tab on the blower housing.

From the service pointer:

Apply a coating of medium strength   
    thread lock   (Thread lock 242 -part   
    # 4210460) to the entire length of threads 
    on the blower shaft.


 

Need help on belt replacement for Maytag dryer

Started by phlip2red

Replies: 6
Views: 10996
Last post May 31, 2008, 11:40:09 AM
by AJ
Maytag Performa Dryer Belt

Started by trialnerror

Replies: 6
Views: 8008
Last post June 17, 2008, 04:42:20 PM
by JWWebster
Maytag Performa Dryer Belt replacement

Started by feehar

Replies: 1
Views: 21486
Last post July 07, 2008, 11:10:47 PM
by Repair-man
Maytag Dryer step by step belt replacement instructions

Started by rmasten

Replies: 2
Views: 63867
Last post July 10, 2008, 07:07:55 AM
by Repair-man
belt replacement on maytag dryer LDE8414ACE

Started by markg

Replies: 2
Views: 7947
Last post October 15, 2008, 11:30:12 AM
by JWWebster
Y312959 Maytag Dryer Belt

Started by AJ

Replies: 0
Views: 5064
Last post April 16, 2009, 08:05:56 AM
by AJ