Author Topic: Replacing rear bearing on White Westinghouse stackable dryer  (Read 11249 times)

Offline bibico

  • VIP Member
  • Member Since: Mar 2008
  • Posts: 6
My stackable dryer is showing all the squeaky signs of a rear bearing in need of replacement.

I believe the part number I need is 5303281153

I've found information on how to get at the bearing on a conventional stand-alone dryer, but can't figure out how to get at it on this stackable.

If anyone knows whether I need to pull the drum from the front or get at the bearing from the back of the unit, I'd be grateful for guidance. I can't tell if the screws on the inside of the drum are what's holding the thing in place. I hate to start unscrewing stuff only to find out there was a more direct route!

Model MLXE42REW0

Also, if you know of any special precautions for the disassembly / reassembly, I'd be happy to hear them.

Thank you for any help on this.

Offline BrntToast

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 388
  • Mayday Appliance Service
    • frigidaire service blog
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #1 on: March 31, 2008, 09:13:04 PM »
rear bearing can be changed with dryer stacked on washer(you need enough room above the dryer to tilt the lid open)
there are 2 spring clips under the front of the lid(push them in with a putty knife) then lid tilt up, the front panel is held on by 2 screws on the inside, then the front panel pulls away and lifts off 2 clips on the bottom
once front is off you reach in on the right hand side and disconnect belt from the idler pulley, drum will now lift up from the back(the rear bearing is a round ball that sits inside a reciever)
drum pulls out from the front
remove bearing from the dum and reciever from the cabinet
tips....  if the drum doesn't wanna lift up you can remove the 3 center screws from the drum and pull drum out then wiggle old bearing apart
tip2... the lil steel ball bearing in the kit goes into the back of the white plastic socket(beveled on the back) use a dab of greese to keep it from falling
last tip... the replacement that goes on the drum does not have the holes pre-threded, so thread them first(with the old screws)throw away the ones in the kit if they are phillips cause they strip before they ever tighten enough

to clarify one thing you said earlier.... your dryer is a free standing dryer, its just stacked on a washer, all the instructions you have for a free standing one are identical(with the exception of the dryer being 4 feet in the air)
« Last Edit: March 31, 2008, 09:16:58 PM by BrntToast »
Mayday Appliance Service
Winnipeg Manitoba Canada


The only stupid question is the one not asked

Offline bibico

  • VIP Member
  • Member Since: Mar 2008
  • Posts: 6
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #2 on: March 31, 2008, 09:32:40 PM »
Wow, thank you for the great information BrntToast. I'm actually sort of looking forward to giving it a shot.

I'll make sure to take some good photos of the process in case they might be of interest to anyone in the forums. I know that this is a fairly common problem, so if I can post any pictures in a subsequent reply I'll do that. Otherwise I'll look at posting in the photo galleries.

Thank you again for the fast reply!

Offline BrntToast

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 388
  • Mayday Appliance Service
    • frigidaire service blog
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #3 on: March 31, 2008, 09:39:51 PM »
one tip i forgot... do NOT use the whole tube of greese!!!!  you need only fill the cup to the bottom lip

save the extra greese, once a year if you can reach behind the machine you can push the tube against the metal bracket that holds the lil ball bearing in place(this is where you will see all the wear and where the squeak usually starts

Mayday Appliance Service
Winnipeg Manitoba Canada


The only stupid question is the one not asked

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9599
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #4 on: March 31, 2008, 09:42:00 PM »
It would be awesome if you could include some photos.

Only the AJ Team members can add photos to the gallery at this time, but you can add them as attachments to your topic right here.

You could also email them to me if you would like and I can add them to the gallery and then to your topic here.

Will be looking forward to seeing the photos.  O0
Hope you find our website helpful.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #5 on: March 31, 2008, 10:48:49 PM »
this may be a close model number

MLXE42REW6 Parts Manual
« Last Edit: March 31, 2008, 10:52:09 PM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline bibico

  • VIP Member
  • Member Since: Mar 2008
  • Posts: 6
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #6 on: March 31, 2008, 11:13:52 PM »
Hi again,
It looks like the manual is a bit closer to what I have than what BrntToast was describing. This is going to be a bit of an adventure, since I already managed to take off the front of the dryer, though it wasn't secured the way most dryers are. There are a number of screws to remove, the control panel to move out of the way, the power switch cord to disconnect, etc. I'm sure with full size floor models there's a bit more room to maneuver, as well.
I'm saving the attempt to remove the drum for tomorrow, since it's late. I think I know what the idler pulley looks like, but I'm having some doubts about it being easy to replace when I go to reinsert the drum...not sure if the belt comes out with the drum. I'm actually wondering if this could have been done from the back side of the dryer instead, because I think the idler would be easier to reach then. Before taking out the drum I'll probably pull out the unit, get behind it, remove the back panel and have a look.
Heck, I'm doubting it'll ever run again at this point, so why not! I'll post some photos tomorrow if I get some that show clearly what I'm talking about. I'd guess that anyone who ever owned a condo (like me) or an apartment has run into this.

More on this as it develops. Thanks again for the information!

Offline BrntToast

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 388
  • Mayday Appliance Service
    • frigidaire service blog
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #7 on: March 31, 2008, 11:32:39 PM »
i gave instructions for the model number from the last topic you posted in... if you have a machine that looks like the manual reg posted, you have a laundry center not free standing dryer  :-\

and yes, you are correct, the only wayto get the belt on a laundry center is from the back(the small access panel) DO NOT!!! remove the whole back panel!!! i repeat DO NOT, the screws are for assembly only, not service

laundry center tip, when reinstalling front panel, loosely attach top screws, then with front panel about 45 degrees from the front of the dryer, open dryer door, reach in and push up on drum, now you can look up and inside the drum and slowly lower front panel down so the drum rests ontop of the felt on the front panel
if the drum isn't lifted enough the front will just bind on the felt

sorry i didn't catch the laundry center bit the first time, i had looked up the model from the first post you made in another topic
« Last Edit: March 31, 2008, 11:46:42 PM by BrntToast »
Mayday Appliance Service
Winnipeg Manitoba Canada


The only stupid question is the one not asked

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Replacing rear bearing on White Westinghouse stackable dryer
« Reply #8 on: March 31, 2008, 11:38:03 PM »
If that is that stack dryer washer that i think it is you can remove the idler from access of a small panel in the rear. The basic setup is the same but the way i was thinking was a friend of mine blew a fuse in hers. An I seem to remember taking something loose from the back and getting the top off and then the front came off. Hell i cannot remember. But the bottom dollar is the tub has to come out the front. The part you have to repair is a standard what we in the appliance parts business call a trailer hitch. If it is worn out it is gonna come out with no problem. if it is left to keep going it will make the tub colapse into the heating element and have a melt down(not good) The bearing will eat its way down to china and on the way it will take out the heating element with it. By gosh that is chicken soup!
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline bibico

  • VIP Member
  • Member Since: Mar 2008
  • Posts: 6
I will post a full account of this ordeal...er...fun project tomorrow, along with some photos. Assuming, of course, that when I reinstall everything and press the start button the thing actually works!

I've learned some things that perhaps will help others who have these stackable units, or who have to work on them. The equation certainly changes when you are working on a stacked w/d with the dryer on top, in a relatively small bathroom where the w/d is installed in a sort of linen closet and you find out that you have to pull the unit out and somehow find room to yank the drum. I really wish I had a video of this, because you'd all get some laughs out of the colorful language....I know my cat won't come near me right now (long story...he'll be fine once he gets over his fear of ladders...).

The inside of my dryer is now almost as clean as the day it was made. That's one benefit of tearing this thing apart and being able to get at all the lint and stuff that collects inside your dryer over the course of years.

I have lots more to say about the engineering that goes into these things: mainly, I'm amazed they work as long as they do without simply collapsing into a heap of cheap aluminum dust and twisted metal!

More on this saga when it's over, but right now my nerves are so jangly that I think I might just go have an adult beverage to celebrate reaching the halfway point.

If any of you have ever pulled a motor out of a VW Bug, you will understand that this is a similar process: the first time you learn all the tricks, and the second time it takes 1/3 of the time to do it.

Thanks again to everyone who's contributed advice, tips, and moral support. I'll be back with narrative and photos very soon.

 

Noisy Frigidiare Dryer - Replace Rear Bearing.

Started by AJ

Replies: 3
Views: 6933
Last post March 31, 2008, 08:25:34 PM
by Al Capone
White Westinghouse Dryer Drum Not Turning

Started by TechnicianBrian

Replies: 0
Views: 4449
Last post May 09, 2008, 09:50:14 PM
by TechnicianBrian
DE800KDW4 Timer Wiring Question - White-Westinghouse Dryer

Started by beaker

Replies: 5
Views: 3490
Last post September 19, 2008, 04:29:23 PM
by Repair-man
WE25X10001 GE, Hotpoint, RCA, Frigidaire Dryer Rear Bearing Kit

Started by AJ

Replies: 0
Views: 3667
Last post April 13, 2009, 12:51:19 PM
by AJ
Fisher and Paykel Dryer rear drum bearing replacement #DEGX2-96102-A

Started by Washaman

Replies: 2
Views: 2663
Last post March 17, 2012, 09:26:50 PM
by Washaman
What grease to lubricate dryer bearing?

Started by JosephK

Replies: 4
Views: 22251
Last post January 16, 2008, 01:44:18 PM
by JWWebster