Author Topic: GE profile fridge repair not going so well!  (Read 4389 times)

Offline Ronyeager

  • VIP Member
  • Member Since: Jun 2011
  • Posts: 170
GE profile fridge repair not going so well!
« on: June 11, 2011, 07:45:46 PM »
Hello, so I have a customer that knows I am a appliance repair man in training and he gave me a shot to fix his fridge anyhow.  Yesterday I ended up replacing the heater, I am certain that was bad.  but, today it shut off again and melted all his ice cream and his food is going bad.  

This GE model actually does not have a main board that I am aware of.  I got a hold of the timer and turned it so it would kick out of defrost mode and the fridge kicked on, but, only for a few minutes then shut off.  I repeated the process and the same thing happened until it shut off all together.  I could not get it to kick back on even when screwing with the timer.  

I was thinking it could be the start relay, but, I am not hearing any clicking noise which would usually indicate that it is bad.  I do not want to just guess on parts and I need to have this thing fixed by monday if I can.  If someone could PLEASE give me some insight on what my problem is here I would really appreciate it.  

Thanks, and since I am learning all this stuff I will be posting more questions then answers on this site.  Sorry for being such a burden!

Model TPX21PRDABB


Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: GE profile fridge repair not going so well!
« Reply #1 on: June 11, 2011, 08:38:12 PM »
First, calm down.
Second,analyze what is wrong.
You have power to the unit.
That is good.
The power goes to the defrost timer and cold control,then to the compressor and condenser fan motor.
You can ohm the cold control to see if it is Good or not.
If no good,jump it out for test only,to see if the compressor and fan motor come on.
If you have power to the compressor start relay and it does not run,ohm the compressor terminals on CSR to see if it is shorted or open.
If the compressor reads OK,replace the start relay.
If no power to the compressor and the cold control is OK or jumped out,suspect a bad defrost timer.
Why was the heater replaced?
Take a Kid fishing.

Offline Ronyeager

  • VIP Member
  • Member Since: Jun 2011
  • Posts: 170
Re: GE profile fridge repair not going so well!
« Reply #2 on: June 11, 2011, 08:45:37 PM »
The heater was replaced because there was a bunch of frost on the coils and I checked the heater with multimeter and I got no reading.  Just by looking at the heater I looked like it was blown out.  btw, I am not sure I know how to check the compressor like you explained.  How do I check the cold control?

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9587
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: GE profile fridge repair not going so well!
« Reply #3 on: June 11, 2011, 08:47:03 PM »
Looks like JT has you pointed in the right direction.  O0

Quote
Thanks, and since I am learning all this stuff I will be posting more questions then answers on this site.  Sorry for being such a burden!

That's what we are here for. After you get some experience you can return the favor by helping answer questions, until then feel free to ask all the questions you want.
Hope you find our website helpful.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: GE profile fridge repair not going so well!
« Reply #4 on: June 11, 2011, 08:54:12 PM »
Just jump the cold control's 2 live wires to see if she runs
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline Ronyeager

  • VIP Member
  • Member Since: Jun 2011
  • Posts: 170
Re: GE profile fridge repair not going so well!
« Reply #5 on: June 11, 2011, 08:58:46 PM »
Okay, I see where you guys are going with this.  But, to ensure I don't blow anything up.  By jumping the cold control I am really just by passing the cold control, correct?  Also, exactly how do I accomplish doing that?  Just track down the proper wires and wire nut them together?

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: GE profile fridge repair not going so well!
« Reply #6 on: June 11, 2011, 08:59:22 PM »
The heater was replaced because there was a bunch of frost on the coils and I checked the heater with multimeter and I got no reading.  Just by looking at the heater I looked like it was blown out.  btw, I am not sure I know how to check the compressor like you explained.  How do I check the cold control?
The cold control is the Off/On thermostat and has 2 wires going to it.
Unplug the fridge.
Remove the 2 wires from the cc and jump them together.
Plug the box back in.
Check for power at the compressor/fan motor.
If they come on and run OK,replace the cold control.
If they do not come on,turn the defrost timer to make sure it is not stuck in defrost.
If still no power,replace the defrost timer.
Take a Kid fishing.

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: GE profile fridge repair not going so well!
« Reply #7 on: June 11, 2011, 09:01:03 PM »
Your power goes to the CC first then to #3 terminal on the timer and out to the compressor on #4.
Take a Kid fishing.

Offline Ronyeager

  • VIP Member
  • Member Since: Jun 2011
  • Posts: 170
Re: GE profile fridge repair not going so well!
« Reply #8 on: June 11, 2011, 09:05:05 PM »
okay I think I am getting cold control confused with the defrost thermostat in the freezer.  The cold control should be next to the timer on the fridge side, right?  or is the cold control that same thing as the round defrost thermostat in the freezer side?  Just trying to put it all together

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: GE profile fridge repair not going so well!
« Reply #9 on: June 11, 2011, 09:07:50 PM »
The cold control is the Off/On thermostat and has 2 wires going to it.
Take a Kid fishing.

 

Repair Guide: Whirlpool Refrigerator - Water in bottom of fridge under drawers.

Started by AJ

Replies: 3
Views: 87913
Last post July 08, 2007, 12:04:06 PM
by curtis
Whirlpool fridge leaking in fridge side... Help Repair-man

Started by Calbo

Replies: 1
Views: 3166
Last post July 29, 2009, 08:12:20 PM
by jumptrout51
MTS16BBMDLWW Moffatt Fridge Repair Please Help!

Started by Sanj

Replies: 6
Views: 2885
Last post November 09, 2009, 12:25:14 PM
by jumptrout51
GE profile performance fridge does not work after moving on the side

Started by rjsto

Replies: 2
Views: 2948
Last post August 02, 2010, 05:52:07 PM
by shieldcracker
GE Profile Fridge, Dual, Separated Defrost Coils Glow Different

Started by Rawfist

Replies: 1
Views: 1856
Last post August 25, 2011, 09:43:35 AM
by tgoods
ge profile fridge

Started by srodt1

Replies: 5
Views: 1206
Last post October 04, 2011, 09:01:29 PM
by niobrara