Author Topic: GE Washer stops right before spin cycle is supposed to start  (Read 3928 times)

Offline oldguard

  • VIP Member
  • Member Since: May 2011
  • Posts: 3
My GE washer just started stopping just before it is supposed to start  it's spin cycle.  Just sits there until I come in and bump it along a bit.  Can anyone tell me what I can do to fix it?

Thanks

OG

Model WCXR1070TAWW


Online niobrara

  • Technician
  • Member Since: Sep 2009
  • Posts: 1172
Re: GE Washer stops right before spin cycle is supposed to start
« Reply #1 on: May 22, 2011, 02:38:47 PM »
Take the front off. On the top of your motor is a flashing led ,watch and see what the number of flashes are. You have a mode shifter that has two wires going to the motor, you can also remove the connection and ohm those two wires.

Offline oldguard

  • VIP Member
  • Member Since: May 2011
  • Posts: 3
Re: GE Washer stops right before spin cycle is supposed to start
« Reply #2 on: May 22, 2011, 03:12:44 PM »
What does the number of flashes tell me?  Do I start the washer and let it run until the lights flash? 

Also, what do you mean by "...you can also remove the connection and ohm those two wires"?

I am a newbie at this.

Thank you.

Online niobrara

  • Technician
  • Member Since: Sep 2009
  • Posts: 1172
Re: GE Washer stops right before spin cycle is supposed to start
« Reply #3 on: May 22, 2011, 05:28:20 PM »
Sorry I was on the run.First the flashes are codes that tell sometimes what is wrong with the machine.At the front of your motor there are wires connected.With the power off unhook the connector that has two wires going to the mode shifter.That is what runs the agitate and spin. Then ohm the two wires and tell us what it reads. In the consul on the top should be a tech sheet .Take the 3 screws out of the top back and the plastic consul slides to the side and off.Do not yank on it the tabs break easily.

Offline oldguard

  • VIP Member
  • Member Since: May 2011
  • Posts: 3
Re: GE Washer stops right before spin cycle is supposed to start
« Reply #4 on: May 22, 2011, 05:46:47 PM »
Ok, but I don't have an ohm meter.  I will have to see if my neighbor has one.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: GE Washer stops right before spin cycle is supposed to start
« Reply #5 on: May 23, 2011, 09:43:55 AM »
The motor blinks on and off all the time.
 It blinks faster when running.
If a failure occurs you will get the following flashes:

1 flash bad motor
2 flashes slipping belt
3 flashes corrupted software bad motor
4 flashes failed mode shift circuit
5 flashes bad motor
6 flashes locked motor check for objects between tub
7 flashes bad lidswitch.
8 flashes motor overheated too much soap
9 flashes brake resister is toast bad motor.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Washer makes fast tapping noise at start of spin cycle

Started by Rubik

Replies: 9
Views: 5641
Last post May 04, 2009, 09:03:24 PM
by JWWebster
GE washer stops mid cycle & wont spin out completely

Started by kstump27

Replies: 2
Views: 7849
Last post July 07, 2009, 06:23:24 AM
by Repair-man
Washer stops mid cycle and then the start button flashes

Started by Jaytag

Replies: 16
Views: 8333
Last post October 26, 2010, 06:30:32 PM
by JWWebster
Kenmore washer stops at spin cycle 110.44836300

Started by browniiiz

Replies: 5
Views: 1621
Last post May 03, 2012, 08:13:35 PM
by jumptrout51
Front Loading Washer Model#WCVH6800J1MR Stops before going into spin cycle

Started by sertich11

Replies: 4
Views: 1986
Last post July 02, 2012, 04:07:23 PM
by rego
Washer stops mid cycle. Wont spin. replaced door lock

Started by Sandinmaheye

Replies: 7
Views: 1693
Last post March 03, 2013, 12:42:49 PM
by Sandinmaheye