Author Topic: Maytag washer spin problem  (Read 1576 times)

Offline Bill

  • Technician
  • Member Since: May 2008
  • Posts: 45
Maytag washer spin problem
« on: February 01, 2011, 01:37:52 AM »
Washer would not spin. Found unit to have worn thrust bearing assy. Replaced thrust bearing and washer worked fine for 3  loads then would not spin. Opened lid on washer and attempted to turn tub. Tub turned approx 1/4 to 1/2 rotation then locked down. now washer is spinning properly but don't know for how long. Do yo think this could be a brake problem. Replaced brakes before but usually their was a squealing sound when the unit stopped abruptly. Also wonder if this could be a transmission problem. Any helpful advice will be greatly appreciated.
Bill W.

Model MAV8260AWQ

Offline pigbee

  • Technician
  • Member Since: Feb 2011
  • Posts: 5
Re: Maytag washer spin problem
« Reply #1 on: February 02, 2011, 04:49:48 PM »

bill

when you installed the thrust bearing kit, which washer did you use, the thick one or the thin one?

Offline Bill

  • Technician
  • Member Since: May 2008
  • Posts: 45
Re: Maytag washer spin problem
« Reply #2 on: February 03, 2011, 11:23:33 AM »
Don't remember for sure but when I rotated the pulley to check engagement is was right in the center of the required settings

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Maytag washer spin problem
« Reply #3 on: February 03, 2011, 05:10:08 PM »
It could be a brake problem but you'll need a $100 tool to find out. Same with the tranny, only 2 more tools.

How was the spin noise prior to you doing the repairs...loud?
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Maytag washer spin problem
« Reply #4 on: February 03, 2011, 05:17:20 PM »
If you have too many washers the tub will turn during wash mode and all the clothes will be knotted to hell. If you have too few washers it won't release the tub for spin. The squealing brake can be easily fixed with WD40.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Maytag Washer Spin & Drain Problem

Started by lulubovary

Replies: 1
Views: 1888
Last post March 11, 2008, 04:43:09 PM
by Repair-man
Maytag Washer Model #PAVT234AWW Spin Problem

Started by iceman

Replies: 0
Views: 1476
Last post October 06, 2011, 08:36:46 PM
by iceman
Maytag washer mah4000aww spin cycle

Started by evo100

Replies: 1
Views: 1842
Last post December 25, 2007, 09:41:02 PM
by AJ
maytag washer- timer problem?

Started by inot66

Replies: 6
Views: 4178
Last post January 10, 2008, 08:47:16 PM
by inot66
Maytag Neptune Washer - No Spin

Started by AJ

Replies: 6
Views: 4691
Last post February 20, 2008, 12:41:13 PM
by AJ
Maytag washer noise during high speed spin

Started by madbchron

Replies: 2
Views: 1608
Last post February 05, 2008, 10:03:59 AM
by JWWebster