Author Topic: G E side by side no fan motor evap comeen on  (Read 2343 times)

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
G E side by side no fan motor evap comeen on
« on: December 21, 2010, 11:23:57 PM »
Ello agin fellas well this ref has a mother board and a relay is clicken.I. disconected it from the wall I hoped it would reset? It did not.I then un pluged ref then discounected wire plugs from board.re pluged to wall.re unpluged.re pluged the board now the relay on the board stoped clicken.but still no evap fan.compressor does come on..I did not check voltage to evap motor..motor is not hot hot .as if burnt..and yes I should have checked for volts.... price on a new board is 165......any one got an opinion??....thanks

Model GSS25IFRE  BB
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: G E side by side no fan motor evap comeen on
« Reply #1 on: December 21, 2010, 11:44:51 PM »
How good are you at soldering?
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline ryan111

  • Technician
  • Member Since: Aug 2010
  • Posts: 196
    • Appliance-repair-it.com
Re: G E side by side no fan motor evap comeen on
« Reply #2 on: December 21, 2010, 11:50:51 PM »
Since the board was clicking you will have to replace the board. A bad fan can cause the board to fail. This doesn’t happen often but it can and does happen. Most of the time when the fan causes the board to fail a resistor on the board will burn out. Look closely at the board near the J2 connector and see if there is a resistor burnt. If so you will need to replace the board and the fan.

However the clicking board is normally something different entirely. Often the low voltage side of the board being too weak when something such as the fan or dispenser tries to draw current on it. A bad relay can also cause this. One more thing looks at the back of the board just behind the high voltage relays (bottom of the board) and check for a loose or brunt solder joint. This is worth checking into but it usually will not cause the fan not to run.

This page will help with checking voltage for the fan.  

 http://www.appliance-repair-it.com/refrigerator-fan-motor.html        
« Last Edit: December 21, 2010, 11:55:55 PM by ryan111 »
http://www.appliance-repair-it.com/
Where everyone can repair it!

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: G E side by side no fan motor evap comeen on
« Reply #3 on: December 22, 2010, 04:43:16 AM »
Thank you RYAN
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

 

frigidaire side by side - compressor, evap fan, no voltage at start up relay. w

Started by cstultz

Replies: 0
Views: 762
Last post July 15, 2013, 03:53:18 AM
by cstultz
Fridge evaporator motor variable fan speed - GE Side by side

Started by cot266

Replies: 12
Views: 1396
Last post June 02, 2014, 10:01:38 PM
by dab147315
Whirlpool ed5fhaxss00 side by side no ice

Started by sandy

Replies: 4
Views: 5363
Last post July 20, 2007, 07:07:46 PM
by AJ
Side by Side Refrigerator - Model: frs6r5embf

Started by Savage702

Replies: 1
Views: 2604
Last post June 06, 2012, 04:08:13 PM
by AJ
LG Side by Side Refrigerator Service Repair Manual

Started by AJ

Replies: 0
Views: 5755
Last post May 02, 2008, 12:41:41 PM
by AJ
GE side by side refridge/frost free

Started by inot66

Replies: 9
Views: 6101
Last post May 07, 2008, 06:33:19 AM
by inot66