Author Topic: Maytag Refrigerator HELP..old tech in need of info ref .board/display gone nuts  (Read 6367 times)

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
The display has gone nuts,I've replaced the board same thing happens behinde the board ther is a 3 pron connection if I remove the connection board displays o k what circuit is this and is the board measuring a resistence in this circuit that could be out of range? It also has a evap fan motor that is not starting all the time could some one please help.thanks

Model mfi2568aes
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline Johns Repair

  • Technician
  • Member Since: May 2010
  • Posts: 25
  • Country: us
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #1 on: October 22, 2010, 10:16:59 AM »
Did you replace the display board or the control board? Is the ice chute door flap opening and closing on its own? What exactly is it doing?
 If its not running and the flap keeps opening and closing the main control board needs replaced.

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #2 on: October 22, 2010, 01:09:32 PM »
Yes the ice chut is doing just that the bourd I replace is the one rightbehinde the display, part # 67006294


where would the other board by?
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline Johns Repair

  • Technician
  • Member Since: May 2010
  • Posts: 25
  • Country: us
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #3 on: October 22, 2010, 01:32:38 PM »
It is on the back of the refrigerator. Standing behind it, it will be on the left side a little lower than half way up.
Its got a small cover panel that comes off then you will be at the board, part # 12920710

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #4 on: October 22, 2010, 01:51:21 PM »
Thank you sir.now the compressor does run.I realy appreciate you web site and help.I'm in deep south texas if I can ever help please give me a holler thanks agin
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline Johns Repair

  • Technician
  • Member Since: May 2010
  • Posts: 25
  • Country: us
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #5 on: October 22, 2010, 02:22:41 PM »
Your welcome

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #6 on: October 28, 2010, 10:56:35 AM »
I've installed the main controle board.now on the display I'm getting a PEOOOO code did the main board{old}board damage the new display board?
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #7 on: October 28, 2010, 10:58:47 AM »
I believe you have to program the new board with the code in the model number sticker.
Take a Kid fishing.

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #8 on: October 28, 2010, 11:32:51 AM »
How is that done?
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #9 on: October 28, 2010, 11:58:24 AM »
It's wanting you to insert a code (to validate it) which is located on the serial number plate. The program code number is after after the word CODE. The program code PE0000 will not allow the machine to run. So find the code and enter it by using the control panel buttons and then once the correct code is in there hold the freezer temp down button till the code flashes. That saves it then hit any key to exit the programming mode. Simple ain't it. LOL I am hoping another tech will come in and simplify that proceedure. I ain't worked on these late models. I am old school too.
« Last Edit: October 28, 2010, 12:00:07 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #10 on: October 28, 2010, 01:01:07 PM »
Open the fresh food door and hold the fresh food door light switch closed while pushing the freezer temperature down button pad 3 times within 10 seconds.

Release the FF door light switch.
The control will display PE.
When you see PE press the freezer down button one more time.

To set the code press the freezer up key to the code number.
Then press the refrigerator up key for the nex5t code digit.
Once the code is entered press the freezer down key until the code flashes.
When it flashes the code is saved.
It will take a couple minutes for the compressor to come on after the code is set.
« Last Edit: October 28, 2010, 01:04:37 PM by jumptrout51 »
Take a Kid fishing.

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #11 on: October 28, 2010, 04:33:16 PM »
Thank you jumptrout.I WILL TRY THAT FRIDAY MORNING.I THANK JESUSCHRIST FOR ALL THE HELP.I MUCH APPRECIATE THE SITE :) O0
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #12 on: October 30, 2010, 05:17:07 AM »
Hello well I've done tried to program this ref as advised but the ref is not responding to it.I pressed the FF switch hit/touched the minus area on the freezer 3 times in10seconds still PEO OOO is present never did PE apper I did follow the steps in order jumptrout I would appreciate some futher advice.and would ther be a tech manuel onthis ref inthe manul section of the web site I am determined to work this problem out..alaluya!!!:)
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #13 on: October 30, 2010, 06:08:27 AM »
Mr. Sanchez;

The new control came with good instructions as to how to do this. However, some folks need a visual aid instead of writing to see how things like this are done. The following video explains how to program the Maytag Jazz board:

Jazz Board service
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline williesanchez69

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 37
  • 2 Tim 1;7
Re: HELP..old tech in need of info ref .board/display gone nuts
« Reply #14 on: October 30, 2010, 08:06:00 AM »
Thank you.well the new board I got came with no instructions I need to call my parts store thank you
2 Tim 1;7 God has not given us a spirit of cowerdness but of power,love and a sound mind The problem of the world is not its economy.but the real problem is SIN

 

61005988 Maytag Refrigerator Adaptive Defrost Control Board

Started by AJ

Replies: 4
Views: 10123
Last post February 19, 2011, 07:44:34 PM
by RegUS_PatOff
W10165748 Maytag Amana Refrigerator Control Board Kit

Started by AJ

Replies: 0
Views: 5077
Last post May 31, 2009, 11:43:16 AM
by AJ
Maytag Refrigerator Not Cooling, Replaced Deforst Control Board

Started by Ol' Lonely

Replies: 0
Views: 1414
Last post March 26, 2012, 10:19:52 AM
by Ol' Lonely
Where is the ADC board located on a Maytag french door refrigerator?

Started by kenebob

Replies: 8
Views: 2277
Last post August 29, 2012, 03:29:12 AM
by haroldsappliance
Tech Sheet for Maytag Ref. MSD2650HEB? re: adc board

Started by andersenappliance

Replies: 16
Views: 2758
Last post September 24, 2012, 06:49:14 PM
by JWWebster
Maytag Jazz Board in Refrigerator model MBR2262KES

Started by Karin Yehlik Crawford

Replies: 1
Views: 846
Last post August 14, 2013, 08:41:19 PM
by tgoods