Maytag Refrigerator HELP..old tech in need of info ref .board/display gone nuts

[williesanchez69]

The display has gone nuts,I've replaced the board same thing happens behinde the board ther is a 3 pron connection if I remove the connection board displays o k what circuit is this and is the board measuring a resistence in this circuit that could be out of range? It also has a evap fan motor that is not starting all the time could some one please help.thanks

Model mfi2568aes

[Johns Repair]

Did you replace the display board or the control board? Is the ice chute door flap opening and closing on its own? What exactly is it doing?
 If its not running and the flap keeps opening and closing the main control board needs replaced.

[williesanchez69]

Yes the ice chut is doing just that the bourd I replace is the one rightbehinde the display, part # 67006294


where would the other board by?

[Johns Repair]

It is on the back of the refrigerator. Standing behind it, it will be on the left side a little lower than half way up.
Its got a small cover panel that comes off then you will be at the board, part # 12920710

[williesanchez69]

Thank you sir.now the compressor does run.I realy appreciate you web site and help.I'm in deep south texas if I can ever help please give me a holler thanks agin

[Johns Repair]

Your welcome

[williesanchez69]

I've installed the main controle board.now on the display I'm getting a PEOOOO code did the main board{old}board damage the new display board?

[jumptrout51]

I believe you have to program the new board with the code in the model number sticker.

[williesanchez69]

How is that done?

[JWWebster]

It's wanting you to insert a code (to validate it) which is located on the serial number plate. The program code number is after after the word CODE. The program code PE0000 will not allow the machine to run. So find the code and enter it by using the control panel buttons and then once the correct code is in there hold the freezer temp down button till the code flashes. That saves it then hit any key to exit the programming mode. Simple ain't it. LOL I am hoping another tech will come in and simplify that proceedure. I ain't worked on these late models. I am old school too.

[jumptrout51]

Open the fresh food door and hold the fresh food door light switch closed while pushing the freezer temperature down button pad 3 times within 10 seconds.

Release the FF door light switch.
The control will display PE.
When you see PE press the freezer down button one more time.

To set the code press the freezer up key to the code number.
Then press the refrigerator up key for the nex5t code digit.
Once the code is entered press the freezer down key until the code flashes.
When it flashes the code is saved.
It will take a couple minutes for the compressor to come on after the code is set.

[williesanchez69]

Thank you jumptrout.I WILL TRY THAT FRIDAY MORNING.I THANK JESUSCHRIST FOR ALL THE HELP.I MUCH APPRECIATE THE SITE

[williesanchez69]

Hello well I've done tried to program this ref as advised but the ref is not responding to it.I pressed the FF switch hit/touched the minus area on the freezer 3 times in10seconds still PEO OOO is present never did PE apper I did follow the steps in order jumptrout I would appreciate some futher advice.and would ther be a tech manuel onthis ref inthe manul section of the web site I am determined to work this problem out..alaluya!!!:)

[Repair-man]

Mr. Sanchez;

The new control came with good instructions as to how to do this. However, some folks need a visual aid instead of writing to see how things like this are done. The following video explains how to program the Maytag Jazz board:

Jazz Board service

[williesanchez69]

Thank you.well the new board I got came with no instructions I need to call my parts store thank you