Author Topic: Kenmore Washer will not drain or spin, agitates on the agitate lo cylce only  (Read 8355 times)

Offline mattz

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 3
My washer fills up with water but will not agitate, drain or spin. After some internet research I thought that it might be the motor. I pulled the motor off and left it connected. It would not run unless I tapped the shaft, otherwise it just hums. I thought that it was definetly the motor, so I got a new one; it is doing exaclty the same thing. I am suspicious of the starter capacitor, but this is what I get with the Meter. OL one way, 6.65 approx. when I switch the leads.

Lid switch seems OK, it clicks fine and has continuity when closed.

Help! the dirty clothes is piling up!

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Your speed selector switch can be easily checked for continity using the wiring schematic pasted on the inside of the console. If this switch proves to be OK, the timer is your problem.
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline mattz

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 3
Okay, this model does not have an independent speed selector. I am guessing that it is incorporated into the timer. Just about every wire goes into one harness and switch. Any suggestions about which leads I should be checking.

On a second note, as I was running the machine to check the cycling, the water started overflowing (as I was looking up the cost of a new timer). The tube on the water level switch has been removed and put back on as I was moving things around. Is there a way to reset this?

Thanks

Offline BrntToast

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 388
  • Mayday Appliance Service
    • frigidaire service blog
drain machine, disconnect hose then reconnect, that will reset the pressure balance
Mayday Appliance Service
Winnipeg Manitoba Canada


The only stupid question is the one not asked

Offline Big Dave

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 8
I have had several do that. It will be a defective timer not making contact to the directional start winding. Replace the timer and it will run.

 :)

Offline mattz

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 3
That did it. Thanks a lot. Now my next challenge is to figure out what to do with the motor. THe THermal switch on the old one is craked thanks to my curiosity, and I cannot find a new one.

 

Kenmore washer won't drain, agitate or spin

Started by dwolfgram

Replies: 7
Views: 6198
Last post May 12, 2009, 02:53:59 PM
by JWWebster
Kenmore Washer fills but will not agitate, drain, or spin

Started by Statebanc

Replies: 2
Views: 824
Last post April 23, 2013, 07:02:22 AM
by jumptrout51
Inglis Washer won't spin, agitate or drain - faulty transmission

Started by lawdawg

Replies: 9
Views: 9471
Last post January 27, 2009, 07:54:57 AM
by jumptrout51
Kenmore Washer - motor buzzes, fills but no agitate or drain

Started by peschool

Replies: 1
Views: 1954
Last post January 14, 2009, 06:18:27 PM
by RegUS_PatOff
Kenmore 80 Washer wont drain before spin

Started by rharveysr

Replies: 7
Views: 4446
Last post February 06, 2009, 03:45:20 PM
by mem1966
Kenmore Washer 417.43142300 - no spin/agitate. replaced speed contrl brd

Started by dtcaruso

Replies: 5
Views: 5880
Last post November 01, 2009, 11:18:07 PM
by dennisc