Author Topic: pressure switch trying to make sure its set right ge profile washer  (Read 3257 times)

Offline hotpointtech

  • VIP Member
  • Member Since: Aug 2010
  • Posts: 8
hi does any one know where i can get  a manual or a copy of the manual that tells me how to check to make sure the new pressure switch i just installed is set right it seems to sometimes not fill to the proper level and other times it fills correctly.
thanks


Model wpsb8060b0ww

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: pressure switch trying to make sure its set right ge profile washer
« Reply #1 on: August 15, 2010, 08:16:15 AM »
They are preset and should not be changed.
If you have a fill issue,remove the front panel and check the air dome and pressure tube on the side of the tub for blockage or pinching.
Take a Kid fishing.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: pressure switch trying to make sure its set right ge profile washer
« Reply #2 on: August 16, 2010, 09:26:20 AM »
I'm not sure if this will help, but when installing the Tubing on the Pressure Switch,
the Tub must be empty.

After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline hotpointtech

  • VIP Member
  • Member Since: Aug 2010
  • Posts: 8
Re: pressure switch trying to make sure its set right ge profile washer
« Reply #3 on: August 17, 2010, 02:06:41 AM »
this i know iam actualy a tech i have serviced appliances for 23 years.
i just wanted to know if GE had a guide that tells you how many rows up the tub the water is supposed to go for each setting :)

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: pressure switch trying to make sure its set right ge profile washer
« Reply #4 on: August 17, 2010, 08:23:49 AM »
If the switch is intermittent and the tube is clear you need another switch. I have not had any luck monkeying with a water level switch.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: pressure switch trying to make sure its set right ge profile washer
« Reply #5 on: August 17, 2010, 08:22:27 PM »
Check for a pin hole in the air tube.
Take a Kid fishing.

Offline hotpointtech

  • VIP Member
  • Member Since: Aug 2010
  • Posts: 8
Re: pressure switch trying to make sure its set right ge profile washer
« Reply #6 on: August 18, 2010, 01:22:27 AM »
thanks jump and jb webster the tube is hole free as far as i can tell with pressure on one end and the other plugged.
so i say its time for yet another switch the new one worked flawlessly for 7 months got to love this new Chinese parts company for GE

 

Top-load washer overflows but pressure switch and tube are good

Started by nholling

Replies: 1
Views: 2523
Last post December 11, 2009, 09:17:34 AM
by JWWebster
oil leak from under ge profile washer

Started by husker

Replies: 1
Views: 4167
Last post October 14, 2007, 05:42:08 PM
by Pegi
Roper Washer - On Spin cycle will make load buzzing noise, won't spin

Started by kbrettm1977

Replies: 2
Views: 8781
Last post December 10, 2008, 06:55:27 PM
by JWWebster
lOOKING FOR GE PROFILE WASHER SERVICE MANUAL

Started by Bill

Replies: 1
Views: 3161
Last post January 22, 2009, 05:41:55 AM
by Repair-man
GE Profile Washer

Started by 88jrnascar

Replies: 1
Views: 2065
Last post March 01, 2009, 12:20:07 PM
by JWWebster
How do you remove the front panel of the GE Profile Washer

Started by 88jrnascar

Replies: 1
Views: 4397
Last post March 01, 2009, 12:15:13 PM
by JWWebster