Author Topic: 4WFW9600TA Error Code F/35  (Read 3815 times)

Offline tamster

  • VIP Member
  • Member Since: Jun 2010
  • Posts: 1
4WFW9600TA Error Code F/35
« on: June 10, 2010, 10:39:51 AM »
I did the reset thing it said to do in the manual, it worked once :embarassed:...Also I get the "SUD" error before I  get the F/35 error! I am thinking it is the Brain  :D!!!! Hope not!

Offline schaffersapplian

  • Technician
  • Member Since: Oct 2008
  • Posts: 619
  • Country: us
  • Every action has a reaction
    • Facebook
Re: Error Code F/35
« Reply #1 on: June 10, 2010, 01:25:55 PM »
F35

ANALOG PRESSURE SENSOR FAILURE
If this failure is displayed, there is any malfunction of the steamer
component detected by the Steamer Electronic Board.

Possible Causes/Procedure
Check if pressure hose is fixed correctly.
Check if the airtrap is not blocked.
Check if the hose is not blocked.

Make sure you are ONLY using HE SOAP!
Correct usage amounts are as follows:

Regular HE SOAP = 2 Tablespoons
2X HE SOAP = 1 Tablespoon
3X HE SOAP = 1 Teaspoon

The information on the soap usage comes directly from Whirlpool Tech Line.
Authorized Samsung, Electrolux, Whirlpool, GE, Fisher Paykal, and Maytag Servicer with over 10 years experience.

Offline schaffersapplian

  • Technician
  • Member Since: Oct 2008
  • Posts: 619
  • Country: us
  • Every action has a reaction
    • Facebook
Re: Error Code F/35
« Reply #2 on: June 10, 2010, 01:27:40 PM »
Suds code:

SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE
WASH CYCLE)

If suds are detected continuously by the pressure switch during the drain
or spin phases, the washer will fi ll 4 liters of water and during 5 minutes
the unit will rest without tumbling, the water will be drained and it will try
to spin or drain again.

Possible Causes/Procedure

If too much detergent was used:
Run through a RINSE/SPIN cycle.
Run a NORMAL cycle without adding any detergent.
This should clear the unit of the excess detergent.
Check the drain hose and make sure it is not plugged or kinked.
Unplug washer or disconnect power.
Check wire harness connections to the drain pump, pressure switch,
and Central Control Unit (CCU).
Check/clean drain pump filter of foreign objects.
Plug in washer or reconnect power.
Check drain pump.
Check the pressure switch.
Verify CCU operation by running a Diagnostic Test or any cycle.


Try reducing the amount of soap used before digging into the F35 code.  This COULD be directly related.
« Last Edit: June 10, 2010, 01:29:26 PM by schaffersapplian »
Authorized Samsung, Electrolux, Whirlpool, GE, Fisher Paykal, and Maytag Servicer with over 10 years experience.

Offline niobrara

  • Technician
  • Member Since: Sep 2009
  • Posts: 1172
Re: Error Code F/35
« Reply #3 on: June 10, 2010, 06:51:36 PM »
The ones I have had that soap wasn't a issue in I replaced the pressure switch in and problem solved.You can get the switch here,but as Shafer says check the soap issue first.

 

Whirlpool electronic error code

Started by roxgirl

Replies: 1
Views: 5601
Last post July 25, 2007, 08:15:36 PM
by AJ
Whirlpool Duet Washer - F-30 error code and clunking noise in detergent area.

Started by AJ

Replies: 3
Views: 14082
Last post November 15, 2009, 09:34:58 AM
by AJ
Kitchenaid Washer F11 Error Code

Started by TechnicianBrian

Replies: 0
Views: 5444
Last post March 23, 2008, 07:06:27 AM
by TechnicianBrian
error code F-05

Started by longbay102

Replies: 9
Views: 5582
Last post June 12, 2008, 05:41:37 PM
by whirlpooltech
Maytag Washer F01 Error Code

Started by TechnicianBrian

Replies: 0
Views: 7956
Last post June 17, 2008, 07:13:27 AM
by TechnicianBrian
LG Front Load Washer LE Error code

Started by TechnicianBrian

Replies: 43
Views: 102794
Last post March 12, 2012, 08:01:50 AM
by roodog