Author Topic: Dryer Won't Heat  (Read 12363 times)

Offline TSOL68

  • VIP Member
  • Member Since: May 2010
  • Posts: 16
Re: Dryer Won't Heat
« Reply #30 on: May 28, 2010, 01:23:46 AM »
Did you give up on me already?  :)  Tonight I pulled out the drum and tested everything I could get my probes on, everything is in spec with the manual.  I re-tested valve 2 (pink and red wires) at the plug on the main board....Still not getting any voltage after the ignitor goes out.  Valve 1 (red and white wires) gets 100DCv as ignitor is on.  It seems that the mainboard is not getting the signal to open valve 2, could this be the ignitor not getting hot enough for the flame sensor to open the valve?

Thanks Again!

Offline Beehive Appliance

  • VIP Member
  • Member Since: May 2010
  • Posts: 18
    • Beehive Appliance Service
Re: Dryer Won't Heat
« Reply #31 on: May 28, 2010, 02:16:31 AM »
This is where it gets difficult. I would lean towards telling you to try the ignitor. Unfortunately everything else seems to be okay. The ignitor has to be just right for the valves to open. It is merely a safety issue. I have seen it way to often on older machines. From reading the posts and the fact that you have replaced the board, I would replace it.
Beehive Appliance is a family owned appliance repair business in Utah established in 1946. From dishwashers to dryers, we repair it all. If you are looking for expert service at a reasonable price, look no further. Beehive Appliance Service is your solution. Give us a call today! 801-523-8184

Offline TSOL68

  • VIP Member
  • Member Since: May 2010
  • Posts: 16
Re: Dryer Won't Heat
« Reply #32 on: May 28, 2010, 09:41:48 AM »
Ok, I will try that.  This dryer is very heavily used.  3-4 loads a day, and my wife would even warm up the kid's blankets with it.  So maybe  the ignitor is just not getting hot enough

Offline john63

  • Technician
  • Member Since: Feb 2010
  • Posts: 508
Re: Dryer Won't Heat
« Reply #33 on: May 28, 2010, 11:00:56 PM »
The fault is likely the MAIN BOARD.

New parts can be a "dud".

The IGNITER only needs to provide heat for the FLAME SWITCH to "sense" it and to provide a source of ignition of the gas.
Amperage (the gas oven type) has no role in dryer burner ignition.

The gas coils are within specification (ohms).

The MOTOR SWITCH is okay--since the IGNITER functions.

The THERMOSTATS & THERMAL LIMITERS are good---the IGNITER is working.

Generally---when a FLAME SWITCH fails---the IGNITER will not glow or the burner never ignites.

Try replacing the FLAME SWITCH (p/n: 6501EL3001A) as this is not only a possibility but is relatively inexpensive.

If that fails to resolve the problem...

This still leaves the MAIN BOARD & the WIRE HARNESS as the most likely suspects.

« Last Edit: May 28, 2010, 11:20:21 PM by john63 »

Offline TSOL68

  • VIP Member
  • Member Since: May 2010
  • Posts: 16
Re: Dryer Won't Heat
« Reply #34 on: May 29, 2010, 10:37:10 PM »
Can I eliminate the wire harness since I tested voltage by inserting my probes into the plug that attaches directly to the main board?  I will order the flame switch on Tuesday.  Thanks!

Offline Beehive Appliance

  • VIP Member
  • Member Since: May 2010
  • Posts: 18
    • Beehive Appliance Service
Re: Dryer Won't Heat
« Reply #35 on: May 30, 2010, 01:08:00 AM »
Your wire harness is fine. I am attaching a part of a manual which explains how the LG Gas valve flows. The Flame sensor has only a 50 degree spread between open and closed. open @370 closed @350 Have you put an ohm meter on the two leads of the flame sensor while you are trying to run the machine? if so, does it ever open (have no continuity)? this should be open when the ignitor is at its hottest point. I still think you have an issue with the ignitor not getting hot enough or the sensor never opens. One trick you may try is to carefully disconnect  one of the wires to the sensor while the ignitor appears to be heating. Do this with the gas off, and while you are measuring voltage to valve 2. This will tell you if everything above (board, wire harness) is working fine. If you have your voltage at this point you are sure it is either the sensor or the ignitor. I still would try the ignitor first because in my experience the sensors just don't fail that often.
« Last Edit: May 30, 2010, 01:09:34 AM by Beehive Appliance »
Beehive Appliance is a family owned appliance repair business in Utah established in 1946. From dishwashers to dryers, we repair it all. If you are looking for expert service at a reasonable price, look no further. Beehive Appliance Service is your solution. Give us a call today! 801-523-8184

Offline TSOL68

  • VIP Member
  • Member Since: May 2010
  • Posts: 16
Re: Dryer Won't Heat
« Reply #36 on: June 12, 2010, 02:52:37 AM »
OK, I got all of my parts and you are not going to believe this.... I still had the same problem, only 22DCV to the valve 2 plug.  I was about to give up but I decided to put the plug on valve 1 and then test 2 (I was testing with both plugs disconnected) viola!  I have 103DCV.  So I took off each part and tested.  Now I am back to my original equipment and I get 103DCV.  Since the dryer still won't heat, what now?  The gas coils?

Offline Beehive Appliance

  • VIP Member
  • Member Since: May 2010
  • Posts: 18
    • Beehive Appliance Service
Re: Dryer Won't Heat
« Reply #37 on: June 12, 2010, 09:19:23 AM »
What parts did you end up getting?
Beehive Appliance is a family owned appliance repair business in Utah established in 1946. From dishwashers to dryers, we repair it all. If you are looking for expert service at a reasonable price, look no further. Beehive Appliance Service is your solution. Give us a call today! 801-523-8184

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Dryer Won't Heat
« Reply #38 on: June 12, 2010, 09:36:03 AM »
 
(I was testing with both plugs disconnected)
voltages are always tested with devices connected, unless otherwise directed.

back to square one ....
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Dryer Won't Heat
« Reply #39 on: June 12, 2010, 09:59:41 AM »
The valve resistance is 1995 ohms and the ignitor is 185 ohms.  
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

IA84600 Inglis dryer doesn't heat

Started by RickT

Replies: 5
Views: 8273
Last post January 16, 2008, 04:02:42 PM
by JWWebster
maytag dryer model # md 3500 (no heat)

Started by #13

Replies: 5
Views: 7152
Last post December 05, 2007, 07:15:02 AM
by apptech
LG gas dryer wont heat

Started by berniet

Replies: 17
Views: 16118
Last post December 03, 2014, 12:15:07 AM
by BillR625
Whirlpool Dryer - Run, but does not heat.

Started by AJ

Replies: 2
Views: 3769
Last post January 10, 2014, 12:26:55 PM
by fairbank56
Creda dryer runs but makes only a little heat

Started by goldstonemr

Replies: 33
Views: 13672
Last post April 27, 2008, 02:56:23 PM
by Penguin45
No HEAT in Old Broad's Dryer

Started by babs277

Replies: 32
Views: 11087
Last post March 12, 2008, 10:03:43 AM
by JWWebster