Author Topic: Front Load Washer Vibration - Level Leg  (Read 1555 times)

Online AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 8937
  • Country: us
    • Buy me a beer through paypal
    • ApplianceJunk.com - Appliance Repair Help
Front Load Washer Vibration - Level Leg
« on: April 08, 2010, 10:24:41 AM »
In some instances, the front load washer will not be leveled properly during installation.  This video will detail how you can raise and lower the washer to ensure that it is level.

http://mediasuite.multicastmedia.com/player.php?v=fhgckr9g
Hope you find our site helpful.

Offline whirlpooltech

  • Technician
  • Member Since: Nov 2007
  • Posts: 1367
  • Country: us
  • 20 years of experience
Re: Front Load Washer Vibration - Level Leg
« Reply #1 on: April 08, 2010, 10:27:50 AM »
 O0

Offline john63

  • Technician
  • Member Since: Feb 2010
  • Posts: 449
Re: Front Load Washer Vibration - Level Leg
« Reply #2 on: April 08, 2010, 09:46:51 PM »
Leveling a front load washer (as shown in the video) is important for both--preventing "wobble" as well as for appearance.
A new washer & dryer positioned next to each other at the same height looks very neat.

Although most retailer installers *do* level the machines--what REALLY needs to be done--is to add a single large towel into the washer tub and to put the washer in a SPIN ONLY cycle. This will "mimic" an imbalanced-spin condition.
After 3 to 5 minutes the tub will enter a High Speed Spin Mode.
Using a wrenchette (supplied with most new front loaders) a more precise leveling of the washer can be done.
If there's any rocking or thumping sound during ramp-up-to high-speed-spin----adjust the *left* or *right* leveling leg until the noise completely stops.
Lock the leveling leg nuts.

This will NOT solve vibration/noise on wood floors--unless the washer is a brand/model designed specifically for wood floor laundry rooms.

Entering a washer into a Spin Cycle by activating the SERVICE TEST MODE should *NEVER* be done.
In most front load washers--the software feature which monitors the tub for an imbalance condition is DEACTIVATED during the SERVICE MODE.
The result will be an unbelievable amount of vibration/shaking/hopping--far worst than would normally be the case.
« Last Edit: April 08, 2010, 09:48:27 PM by john63 »

 

131268200 Frigidaire Front Load Washer Vibration Shock Absorber

Started by AJ

Replies: 0
Views: 7889
Last post May 02, 2009, 08:55:47 AM
by AJ
Frigidaire Front Load washer making noise.

Started by curtis

Replies: 3
Views: 5427
Last post July 05, 2007, 09:25:04 PM
by AJ
frigidaire front load washer

Started by Mikki

Replies: 6
Views: 4442
Last post October 17, 2007, 04:42:52 PM
by Mikki
Video: Whirlpool Duet Front Load Washer Water Pump Clean Out.

Started by AJ

Replies: 0
Views: 4671
Last post November 28, 2007, 09:58:47 PM
by AJ
Replacing Front Load Washer Pump Model#LHW0050PQ

Started by resapp

Replies: 4
Views: 1598
Last post May 22, 2012, 12:34:13 PM
by AJ
Frigidiare Kenmore Front Load Washer Inner Tub & Tub Bearing Replacement.

Started by AJ

Replies: 5
Views: 5918
Last post March 03, 2008, 03:56:05 AM
by BrntToast