Author Topic: Whirlpool double oven GBD277PDB09 locked after self clean cycle and blank panel  (Read 11387 times)

Offline aaronw112358

  • VIP Member
  • Member Since: Dec 2009
  • Posts: 16
So I have a double wall oven Whirlpool GBD277PDB09 that I have 2 problems with:

1) Display is blank, even after turning off breaker, waiting 10 minutes, and then turning it back on.

2) Top oven is locked, as it appears that whatever failure happened, happened during a self clean cycle, so I can't get in there.

Something like this did happen before, about 3 years ago.  I am not sure if I did the self clean that time, but I don't think so.  They had to replace two parts - CNTRL-ELEC 22 664 8301848 1 and SUB ELEC-CON 22 664 8302319 1

I'm also having some difficulty removing the panel to start to do some diagnostics and I forgot how he removed it when he was here that time - I can't seem to be able to find the missing latch.  So that's my story as of now - anyone have any suggestions?

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Will the oven slide out? If not, try using a flat brazing rod with the end curled over to pull the door latch to the left where it is stuck in the door slot.

I suspect the blank out is the result of a thermal control fuse in the black L1 wire feeding the electronic control, but you'll have to have the door open to access the panel. Here's the tech Sheet so you can see the thermal fuse, etc.

Tech Sheet
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline aaronw112358

  • VIP Member
  • Member Since: Dec 2009
  • Posts: 16
I'm not sure what you mean by slide out - I can't seem to get a good grip on it anywhere to move it out.  I also can't really see any of the latch mechanism when I look with a flashlight at the top.  Do you mean inserting a rod vertically or horizontally?  There doesn't appear to be much space to do it vertically...

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
A rod can be inserted sideways from the left side of the door in some cases where there is enough clearance. This is in order to  grasp the hook on the door latch and pull it leftward to relese the door from it's grip. From there it's all downhill.
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline aaronw112358

  • VIP Member
  • Member Since: Dec 2009
  • Posts: 16
I think I may need a picture or something to understand what you're trying to describe.  There's no way to put anything in the door from the sides unless I remove the trim as well (how do I do that?)

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
 There is a tiny gap between the door and the front of the oven, even though the door is locked. There is plenty of space for a thin brazing rod to slip in there to hook the latch lever and pull it leftward so the door will open.

You never broke into a car with a coathanger?
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline aaronw112358

  • VIP Member
  • Member Since: Dec 2009
  • Posts: 16
Sadly, no, I never had the chance to break into a car with a coat hanger.  Maybe I'll try to take a picture of the gap on the top and figure out what to do with it.  Alternatively, do you (or anyone else) have the service manual for this oven model?

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Yes, try this link:

WP Double Oven Manual (11 MB)
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline aaronw112358

  • VIP Member
  • Member Since: Dec 2009
  • Posts: 16
repair-man, awesome!  I will break out my toolkit at home over the week and see what I can do with this information.  Yes, I will not forget to turn off the breaker FIRST.

Offline aaronw112358

  • VIP Member
  • Member Since: Dec 2009
  • Posts: 16
Thanks again for the tech note, I was able to pull off the side trim and the control panel and detach it from the wiring harness.  I recruited a friend with a multimeter and did some testing.  It definitely looks like the thermal fuse feeding the control panel is  blown.  We tested a couple of paths on the control board and got continuity in the right places, so that seemed to work, but no continuity through the thermal fuse. 

Next question, how do I replace this?  On the tech sheet you linked to, specifically page 3-2 where it has a blow up of the thermal fuse, mine doesn't link to a board connector by itself, it's in a wiring harness with a electrical crimp connector underneath some molded plastic.  I can detach the spade connector from one one, but the other end is a little bit trickier to remove.  What part numbers are associated with this?

Thanks again for all your assistance!

-aw

 

Whirlpool double oven display blank

Started by timpeterson75

Replies: 2
Views: 6108
Last post February 20, 2009, 09:14:06 AM
by timpeterson75
Whirlpool Oven Shutoff during Clean cycle. Now Oven won't turn on.

Started by Wrangler07

Replies: 0
Views: 955
Last post March 19, 2013, 03:44:52 PM
by Wrangler07
Whirlpool Built in oven clock is blank and oven beeps when not on

Started by Ryan

Replies: 4
Views: 3274
Last post August 06, 2008, 04:47:54 PM
by Ryan
Kitchenaid Double Oven no Heat after Self Clean

Started by TechnicianBrian

Replies: 0
Views: 5556
Last post November 18, 2008, 02:03:23 PM
by TechnicianBrian
Error codes for whirlpool double wall oven

Started by decihlar

Replies: 1
Views: 5029
Last post April 12, 2009, 11:53:55 AM
by jumptrout51
Jen Air double oven replaced control panel - still having problems

Started by mikevalin

Replies: 1
Views: 1980
Last post May 07, 2009, 09:31:04 PM
by Repair-man