Author Topic: Whirlpool fridge compressor  (Read 3960 times)

Offline jvh75021

  • VIP Member
  • Member Since: Nov 2009
  • Posts: 3
Whirlpool fridge compressor
« on: November 18, 2009, 09:14:05 AM »
I have a Whirlpool fridge with a Matsushita compressor DG51C69RAU6, I failed to get the model number, duh on me.

Last night the start relay clattered and then the compressor overload opened. Since the 12 uF cap checked good I thought I would hot wire it and bump the start winding to verify if it is the start relay or if the compressor has tightened up.

For reference I will use clock face numbers for the terminals. Resistance from 8 to 4was highest at 12.7 ohms, so 12 o'clock is common. However the other two were extremely close 8 to 12 read 6.4 ohms, and 4 to 12 read 6.3 ohms. I wasn't expecting the run and start windings to be this close. I assume the higher reading would be the start winding (8-12). Also, buzzing out the start relay, pin 12 goes to L1 and pin 4 goes to L2, further implying that pin 8 is the start winding.

However I called the lab assistant (who does a lot of appliance work) at my old HVAC school and he stated that pin 4 should be start. My observations suggest otherwise.

If the compressor is getting tight are hard start kits a worthwhile approach? I assume the thermal will kick out again if it gets too tight. The compressor label on listed LRA, not RLA so not sure what is should read but assume it would be around 2.6A or less.

BTW, no terminals were shorted to case and the start relay did not rattle when removed.

Thanks,

jh

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: Whirlpool fridge
« Reply #1 on: November 18, 2009, 02:24:52 PM »
My vote is for the 8 0'clock position being Start.
and Yes. You can use a hard start on this compressor.
Take a Kid fishing.

Offline jvh75021

  • VIP Member
  • Member Since: Nov 2009
  • Posts: 3
Re: Whirlpool fridge
« Reply #2 on: November 19, 2009, 06:59:46 AM »
Thanks for the reply.

Finally gathered enough jumpers to hot wire it last night. Powered it up and touched run to start and away it went. First time it was a big arc. Second time less. Third time it started before I could apply the temporary short.

Wish I could find the horsepower rating so I would know what size hard start to use.

Found the model #: ET1FTTXKQ02

Offline MajorApp

  • Technician
  • Member Since: Feb 2008
  • Posts: 548
  • Country: us
Re: Whirlpool fridge
« Reply #3 on: November 19, 2009, 09:09:33 AM »
 You should be ok with a 1/4 horsepower hard start.

Offline jvh75021

  • VIP Member
  • Member Since: Nov 2009
  • Posts: 3
Re: Whirlpool fridge
« Reply #4 on: November 20, 2009, 07:14:37 AM »
Thanks.

All they had was a half horse kit. I suppose I should put the old overload in series with it in case of power glitches.

jh

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Whirlpool fridge
« Reply #5 on: November 20, 2009, 10:21:49 AM »
The hard start has a overload in it
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Sears (Whirlpool) fridge compressor stopped

Started by ArdentGuy

Replies: 4
Views: 226
Last post August 22, 2014, 04:07:14 PM
by ArdentGuy
Repair Guide: Whirlpool Refrigerator - Water in bottom of fridge under drawers.

Started by AJ

Replies: 3
Views: 84574
Last post July 08, 2007, 12:04:06 PM
by curtis
Whirlpool fridge water dispenser

Started by dragonlady74

Replies: 1
Views: 2583
Last post July 10, 2008, 10:30:31 AM
by Repair-man
Sears Whirlpool side by side fridge mfgr in 2000 ice freezes up at bottom of ice

Started by marky

Replies: 13
Views: 6667
Last post September 20, 2014, 06:56:37 PM
by Rocky L Miller 1
GE 6 years old fridge not cooling, compressor on 24/7?

Started by mdm6713

Replies: 16
Views: 5307
Last post January 14, 2009, 11:05:55 AM
by JWWebster
whirlpool fridge how to change thermostat

Started by cheyane634

Replies: 1
Views: 2232
Last post January 19, 2009, 08:05:46 PM
by JWWebster