Author Topic: Kenmore 80 series issues after installing coupler  (Read 3563 times)

Offline punkncat

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 6
Kenmore 80 series issues after installing coupler
« on: October 07, 2009, 06:48:46 PM »
My machine worked fine, then broke the coupler. I took the machine apart, replaced the coupler, and upon putting it back together had a really bad rubber burning smell. Suspecting that the coupler was not fit flush on the shaft, I took the machine back apart and made the coupler flush by knocking it on with a nut driver as suggested here.

I put the machine back together and it will fill, then nothing until it goes all the way to the spin cyle where it will spin out. It never agitates, or even attempt to try and agitate. I have taken it back apart and checked all connections, the lid switch is good, nothing outwardly obvious as to why it suddenly will not agitate, when it worked fine just moments before.

What do I need to check?

Thanks

Model 110.29882890
« Last Edit: October 07, 2009, 07:44:59 PM by Al Capone »

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore 80 series issues after installing coupler
« Reply #1 on: October 07, 2009, 07:00:37 PM »
While fiddling with the machine you may have made the timer connection get a little bit loose or you might have pinched the plastic tube from the tub up to the  water level switch so check all that.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline Al Capone

  • Administrator
  • VIP Member
  • Member Since: Feb 2008
  • Posts: 409
  • Country: us
    • ApplianceJunk.com
Re: Kenmore 80 series issues after installing coupler
« Reply #2 on: October 07, 2009, 07:02:29 PM »
Hi punkncat,

Could you post the model number for us? The model number can be found on the model/serial number tag that is located on the washer.

Check picture below for possible model number tag locations.



Thanks for posting your questions.
RepairClinic.com - Order now for same day shipping. 365 day return policy!

AppliancePartsPros.com - Over 1 Million Appliance Parts In-Stock. 365-Day Hassle Free Return Policy!

Offline punkncat

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 6
Re: Kenmore 80 series issues after installing coupler
« Reply #3 on: October 07, 2009, 07:11:53 PM »
k, all seems fine, what next?

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore 80 series issues after installing coupler
« Reply #4 on: October 07, 2009, 07:24:59 PM »
You need to get everything back off you have something binding
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline punkncat

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 6
Re: Kenmore 80 series issues after installing coupler
« Reply #5 on: October 07, 2009, 07:25:22 PM »
Model number 110.29882890

Kenmore 80 Series Heavy Duty

Offline punkncat

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 6
Re: Kenmore 80 series issues after installing coupler
« Reply #6 on: October 07, 2009, 07:26:44 PM »
I can remove the pump and turn the motor shaft farily easily. The machine will drain and spin fine. What would be binding up that would allow those functions, but cause it not to agitate?

Offline punkncat

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 6
Re: Kenmore 80 series issues after installing coupler
« Reply #7 on: October 07, 2009, 07:32:57 PM »
I note that upon watching it a bit closer that it only spins for the drain out cycle after the wash and rinse cycle, it will not do the "final" spin either.

Offline Al Capone

  • Administrator
  • VIP Member
  • Member Since: Feb 2008
  • Posts: 409
  • Country: us
    • ApplianceJunk.com
Re: Kenmore 80 series issues after installing coupler
« Reply #8 on: October 07, 2009, 07:45:23 PM »
I updated the topic to include the model number info, thanks.
RepairClinic.com - Order now for same day shipping. 365 day return policy!

AppliancePartsPros.com - Over 1 Million Appliance Parts In-Stock. 365-Day Hassle Free Return Policy!

Offline punkncat

  • VIP Member
  • Member Since: Oct 2009
  • Posts: 6
Re: Kenmore 80 series issues after installing coupler
« Reply #9 on: October 07, 2009, 07:50:16 PM »
Ok, so the motor is supposed to go the opposite way when it is agitating. Why would it not run that direction? It doesn't hum or anything, nothing is bound, but will not run that direction at all.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore 80 series issues after installing coupler
« Reply #10 on: October 07, 2009, 09:59:36 PM »
Ah grasshopper, we is down to the old appliance man problema, motor or the timer syndrome. You gave it away though. The first spin is fine the 2nd ain't? That is a timer malfunction. Remove that timer and take the cheapass pwastic liner off there and look at the barrel with humps in it for burnt marks. Some of them timer knobs screw off others have a pin in the rear end of the timer that must be backed out a tad to release the knob. Let me know. If it is the timer with the solid plastic body then that crappy hunk of lousy mexitronics  :bonk:  is my usual suspect.  :2funny:
« Last Edit: October 07, 2009, 10:03:20 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Old Kenmore 80 Series - Just changed coupler, now nothing works

Started by jordan614

Replies: 1
Views: 1772
Last post September 29, 2008, 05:13:19 PM
by JWWebster
Kenmore 90 Series Washer with Spin Cycle issues

Started by B_con

Replies: 2
Views: 3259
Last post February 28, 2009, 08:27:56 PM
by JWWebster
Kenmore Model 80 washer coupler/tranny issues

Started by Ken More

Replies: 4
Views: 1285
Last post January 08, 2012, 09:27:11 PM
by Ken More
Kenmore 80 Series Washer

Started by shawnrconnelly

Replies: 5
Views: 4597
Last post October 25, 2007, 09:46:52 AM
by Pegi
Kenmore 90 Series - No agitation

Started by jastek

Replies: 24
Views: 8762
Last post February 23, 2008, 06:18:42 AM
by whirlpooltech
KENMORE WASHER 60 series

Started by amnesty

Replies: 7
Views: 12400
Last post March 06, 2008, 02:48:23 PM
by JWWebster