Author Topic: Subzero Questions Please  (Read 3762 times)

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Subzero Questions Please
« Reply #10 on: September 13, 2009, 07:59:47 PM »
... we might even get a nod from President Obama...
or from Al Gore, the inventer of the internet.  :rofl:
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Subzero Questions Please
« Reply #11 on: September 13, 2009, 08:00:40 PM »
Yeah Him too :D Don't fergit my man can pull the plug anytime :D
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline Earl Dryer

  • Technician
  • Member Since: May 2008
  • Posts: 166
  • Country: us
Re: Subzero Questions Please
« Reply #12 on: September 13, 2009, 08:30:11 PM »
None, of you 3 fellers should even consider hanging it up on this site, Ya'll
are my HERO's

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9605
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Subzero Questions Please
« Reply #13 on: September 14, 2009, 05:53:19 AM »
None, of you 3 fellers should even consider hanging it up on this site, Ya'll
are my HERO's

 O0

You can say that again. I may have started the site, but I will be the first to tell you that I'm no expert on all brands.

I learn new things from my own site all the time.

Quote
Never thought I would have degenerative spine disease, but there you have it. Nothing personal.

Sorry to hear that.

Quote
Maybe it's time I quit hanging around here so much.


Don't even think about it buddy! I have learned a lot from your post.

I have always felt very lucky that you take the time to contribute so much to our site when you have a site of your own too, thanks!

btw: I also enjoy Repair-mans site a lot, http://repair2000.com as he can tell you I check it constantly through out the day to see if there is anything new. :)

 
Hope you find our website helpful.

Offline phdee

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 2
Re: Subzero Questions Please
« Reply #14 on: September 14, 2009, 08:32:55 AM »
Well, you bypassed the main board to force it to run, so the symptoms now are a sealed system issue on the FF side. Whether a leak or a restriction, this will have to be determined by a certified refrigeration tech.  All of this will cost about 1/3 the cost of replacing this unit.

BTW, SubZeros always have access valves or pinch-off tubes to do sealed-system diagnostics from. If the unit  is low on Freon or runs excessively, it will cut out. If you don't know what type of refrigerant it has, read the model plate...it  says what kind and how much.


Thank you for your feedbaack!!
It does not have any circuit board, I just bypassed the thermostats, they are both screwed up, do not open and close any where near the correct temps.  I see I can them for about $50 each, no big deal.  I further disected, it is a round device that opens and closes, clicking, I assume this is the thermal over load protector?  Question is, is it bad, or is the compressor drawing too much current?  I also see a relay, that if I understand correctly switches between the start windings and run windings, could that be bad, causing the compresor to run on the start windings?
It is R12, can I still get that recharged?
Thank You !!!

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Subzero Questions Please
« Reply #15 on: September 14, 2009, 12:03:02 PM »
If it blew the thermostats, chance are the compressor is bad or has shorted windings. Regardless, you  may not find anyone with any R-12 in stock to do this for you, and converting the FF side to 134-a requires a new compressor, condenser and evaporator coil. I think I'd be shopping for a new fridge, since you could have a repeat episode on the other side later down the road.
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline krazytech

  • Technician
  • Member Since: Sep 2007
  • Posts: 705
  • Country: us
    • Buy me a beer through paypal
Re: Subzero Questions Please
« Reply #16 on: September 28, 2009, 09:18:55 PM »
You can use R-414b all so known as 'HOT SHOT' . But I find that R-414a works better than R414b. In fact if you do warranty work for Whirlpool's non 134a systems you are required to use R-414a. this is on Whirlpool household Refig. & Freezers. Plus you only use 80% as compared to R-12.
Check the Basics first!!! Read the Manual !!!Buy the tech a Beer!!!

 

Subzero questions and observations

Started by Ricktec

Replies: 1
Views: 390
Last post February 13, 2014, 02:26:17 PM
by Ricktec
550 Subzero ice maker will not stop making ice

Started by pummy

Replies: 3
Views: 4275
Last post May 05, 2009, 07:04:49 PM
by shieldcracker
In door ice maker not working...power questions

Started by sshippee

Replies: 5
Views: 2148
Last post May 10, 2009, 07:42:41 AM
by sshippee
201R Subzero frig only ref charge?

Started by outaluck

Replies: 14
Views: 4168
Last post June 13, 2009, 03:38:30 PM
by JWWebster
SubZero 550 water in refrigerator

Started by dirtrider180

Replies: 9
Views: 4753
Last post February 28, 2010, 04:34:48 PM
by dirtrider180
subzero 532 inlet water valve to ice maker

Started by bjmunroe

Replies: 11
Views: 7991
Last post March 10, 2011, 10:56:44 PM
by bjmunroe