Author Topic: 70 series kenmore 70 series dryer will not turn on  (Read 20841 times)

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
70 series kenmore 70 series dryer will not turn on
« on: September 06, 2009, 03:09:27 PM »
My Kenmore 70 series dryer will not turn back after opening the door and checking on the clothes. Yes I did make sure the door closed all the way and yes it does have power going to it. Please help

Model 110.66722694
« Last Edit: September 07, 2009, 03:35:03 PM by Al Capone »

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: kenmore 70 series dryer will not turn on
« Reply #1 on: September 06, 2009, 03:20:49 PM »
You did everything right so far except to provide the model number
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #2 on: September 06, 2009, 03:25:05 PM »
OK, I think this is the model number 110.66722694

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: kenmore 70 series dryer will not turn on
« Reply #3 on: September 06, 2009, 03:28:34 PM »
You're going to need a volt/ohm meter to find out what failed, most likely it is the thermal fuse or the thermal cutoff. These parts would show full continuity when tested with the OHM meter. Your parts are set up as shown below:

"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #4 on: September 06, 2009, 03:33:00 PM »
sorry for my ignorance, should the dryer be plugged in while I am checking for continuity?

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: kenmore 70 series dryer will not turn on
« Reply #5 on: September 06, 2009, 03:44:16 PM »
No, and that bothers me a little...just how do you know for sure you have 240 volts at the wall plug? You claimed to have power to the dryer, so how did you verify this?

Anyway, continuity checks are done with the power cord unplugged. A meter sends a 9 volt charge thru the part to be tested to see if there is a complete circuit thru it.
« Last Edit: September 06, 2009, 03:48:22 PM by Repair-man »
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #6 on: September 06, 2009, 04:22:07 PM »
The reason I know that I have power to the dryer is because when I turn the dial to any specific I can hear the timer clicking.

I have attached a picture of my OHM meter to see if can tell me what setting I should set it to check the Thermal Cutout and Thermal Fuse for continuity.

What reading am looking for when I am checking these items?

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: kenmore 70 series dryer will not turn on
« Reply #7 on: September 06, 2009, 04:28:20 PM »
On the lower left quadrant is the OHMs section. Set the dial to the lowest setting and place your leads across the 2 wires on the thermal fuse, then the thermal cutout. There should be a reading of 000 or close to zero if the part has a complete circuit. Let me know what it reads after you check it and we'll go from there.
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #8 on: September 06, 2009, 04:31:57 PM »
Ok, checked it and got 0.00

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #9 on: September 06, 2009, 04:58:09 PM »
Should I check the Thermal Fuse?

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: kenmore 70 series dryer will not turn on
« Reply #10 on: September 06, 2009, 05:36:26 PM »
In his absence,YES,check the thermal fuse. also.
Take a Kid fishing.

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #11 on: September 06, 2009, 05:37:50 PM »
Ok, I also checked the Thermal Fuse and got 0.00

Offline RookieJose

  • VIP Member
  • Member Since: Sep 2009
  • Posts: 10
Re: kenmore 70 series dryer will not turn on
« Reply #12 on: September 06, 2009, 05:43:30 PM »
Any other suggestions?

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: kenmore 70 series dryer will not turn on
« Reply #13 on: September 06, 2009, 05:58:58 PM »
If you have got 0.00 meter reading that means that is an open circuit (bad fuse, replace that dude. When it is blown the dryer will not run. Clean out the dryer and vent or that baby will just blow again.
« Last Edit: September 06, 2009, 08:48:55 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline jumptrout51

  • Technician
  • Member Since: Nov 2007
  • Posts: 1879
  • Country: us
    • Buy me a beer through paypal
Re: kenmore 70 series dryer will not turn on
« Reply #14 on: September 06, 2009, 06:03:04 PM »
Other suggestions are check the door switch for continuity. Check the terminal block where the cord connects for 220 volts. Check the start switch for continuity. All these should be checked with the dryer unplugged,except the 220 volts to the terminal block.

JW is correct. Both parts should read ohms/continuity.
« Last Edit: September 06, 2009, 06:04:35 PM by jumptrout51 »
Take a Kid fishing.

 

Kenmore 70 series Elecric Dryer...cuts off

Started by lalakelley

Replies: 12
Views: 5615
Last post February 20, 2008, 12:07:10 PM
by AJ
Kenmore 70 series electric dryer...wont heat

Started by lalakelley

Replies: 53
Views: 36972
Last post November 24, 2011, 02:40:03 AM
by RegUS_PatOff
kenmore 80 series electric dryer

Started by mthd60sprty

Replies: 4
Views: 11209
Last post June 24, 2008, 11:48:30 PM
by RegUS_PatOff
Kenmore 80 series dryer just quit

Started by abomb

Replies: 8
Views: 4469
Last post July 18, 2008, 08:53:56 AM
by JWWebster
Kenmore 70 series dryer won't heat

Started by akwikeee

Replies: 29
Views: 44488
Last post October 29, 2010, 12:37:03 AM
by JWWebster
Kenmore 70 series dryer - no heat

Started by tinker

Replies: 5
Views: 9908
Last post October 01, 2008, 09:38:53 PM
by JWWebster