Author Topic: wbse3120b1ww top loader belt replacement  (Read 2738 times)

Offline propyl

  • VIP Member
  • Member Since: Aug 2009
  • Posts: 2
wbse3120b1ww top loader belt replacement
« on: August 22, 2009, 12:15:50 PM »
Hi appliance junk. You and I have done some chit chatting over at smfhacks and I am in need of your expertise.

I have a wbse3120b1ww washing machine that I believe needs a belt replacement, or at least I hope that's the situation.

I guess the first thing I should note is that I don't know what I am doing at all.

I am struggling to get this thing apart. The back doesn't come off and it appears that the front might if I can remove the lip plate around the top. I have seen on a couple other sites around the net that say the sill plate slides forward and then up. For the life of me I cannot get this to slide forward. I have beaten the crap out of it with a rubber mallet lol and I think it budged about an 1/8 inch.

Do you or anyone else around here know how I can get into this contraption? lol

Heres the diagram that I found from your site

http://www.appliancepartspros.com/partsearch/model.aspx?model_id=229921


Thanks,

Travis


Offline propyl

  • VIP Member
  • Member Since: Aug 2009
  • Posts: 2
Re: wbse3120b1ww top loader belt replacement
« Reply #1 on: August 22, 2009, 12:45:49 PM »
Well I managed to figure out how to get the front off (puddy knife) So much for beating the snot out of it lol.

Now that its apart, the belt appears to be fine. Which leads me to my new question... Now what?

There's a few clicking sounds (appears the relays are all working) but no drive action during the spin cycle. Bad motor perhaps?


Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: wbse3120b1ww top loader belt replacement
« Reply #2 on: August 22, 2009, 02:22:54 PM »
For starters, here the GE topload Service manual so you don't beat any more snot out of your poor washer :)

My usual finding in cases like yours is a bad lid switch, but hey, you already got it apart, so whip the old OHM meter out and do some checking...

GE Kit Lid Switch, part number: AP2620150


"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

donate
$1, $2, $5, $10, $20, $50
 

MAYTAG washer drive belt replacement

Started by chevyt

Replies: 1
Views: 1302
Last post November 05, 2009, 02:50:24 PM
by JWWebster
LWS21AW-3062 SPeed Queen Belt Replacement

Started by Lebz

Replies: 5
Views: 2861
Last post October 13, 2010, 09:37:10 PM
by JWWebster
GE Hydrowave top load washer Belt replacement

Started by JWWebster

Replies: 3
Views: 2832
Last post August 19, 2011, 02:49:36 PM
by JWWebster
Kenmore 70 series? washer wont spin after belt replacement

Started by itsdatoneguy

Replies: 19
Views: 1213
Last post February 06, 2014, 12:57:37 PM
by fairbank56
Video: Whirlpool Made Direct Drive Washer Motor Coupler Replacement

Started by AJ

Replies: 18
Views: 41060
Last post May 18, 2010, 06:53:50 AM
by gimpyjones
whirlpool belt drive washer won't spin

Started by mthd60sprty

Replies: 7
Views: 6813
Last post June 06, 2013, 08:42:12 AM
by fairbank56