Author Topic: Dishwasher skipping cycles  (Read 3253 times)

Offline magfinpete

  • VIP Member
  • Member Since: Aug 2009
  • Posts: 4
Dishwasher skipping cycles
« on: August 11, 2009, 03:36:33 PM »
Hi All:
Frigidaire PLDB988CC0 dishwasher. I've dowwnloaded a service data sheet from Frigidaire that says the normal and light-both racks cycles have two rinse cycles between the pre-wash and wash cycles. When the machine empties from the pre wash cycle, the timer drops 20 minutes and the machine fills for the wash cycle, skipping two rinse cycles. After the wash cycle, the normal and light cycles follow with two rinse cycles, but the Light is only supposed to have one rinse cycle. The pots and pans cycle seems to work fine. Is it the control board, or is it possible that the service data sheet is inaccurate? I'm going nuts! Help! Thanks.

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Dishwasher skipping cycles
« Reply #1 on: August 11, 2009, 04:23:31 PM »
The situation is normal. What you did not see on the literature is regarding the communication between the turbidity sensor and the electronic control. During the pre-wash, the sensor tests the water to see how dirty the load actually is. If there is not much soil seen thru the optic sensor, the control will detract from the wash cycle.

You are not going crazy :)

If the dishes are getting clean, you have no need to worry. Remember not to pre-rinse your dishes in the sink first, just scrape away solids and load 'er up. Too much  pre rinsing causes detergent residue to stay behind and cause other issues later.

If you download the 24" electronic dishwasher manual, it explains the turbidity sensor thusly,

"The true name of the sensor is called the Turbidity
Sensor. It is located just in front of the wash impeller on
the sump. The sensor is mounted by two cross point
head mounting screws.There is a locating tab on the
sensor and a knotch on the sump to ensure the sensor
is intalled correctly. The sensor is a device that senses
how dirty the water is. This is done when the customer
loads the dishwasher with dirty dishes, then starts the
unit. The sensor will then sense how dirty the water is.
The DC output voltage of the sensor will be monitored
at the end of the 30 second pause in the first wash and
the first rinse. If a sufficient quantity of soil exists, the
control will add two additional rinses for a total of eight
fills, or 9.6 gallons of water. Should the sensor detect a
light soil condition, the control will subtract two rinses for
a total of four fills, or 4.8 gallons of water. The Normal
cycle can either increase or decrease the time of a wash
cycle. It just depends on how dirty the water is."
« Last Edit: August 11, 2009, 04:31:52 PM by Repair-man »
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline magfinpete

  • VIP Member
  • Member Since: Aug 2009
  • Posts: 4
Re: Dishwasher skipping cycles
« Reply #2 on: August 11, 2009, 08:26:51 PM »
Thanks for demystifying this.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Dishwasher skipping cycles
« Reply #3 on: August 15, 2009, 03:10:37 PM »
Nice explanation Jimbo. The machine uses the turbidity sensor to save water and power usage. pretty cool feature.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Frigidaire FDB1050REB2 dishwasher doesnt finish cycles

Started by dzlsnowman

Replies: 6
Views: 2044
Last post December 11, 2011, 08:13:18 PM
by dzlsnowman
Dishwasher no longer cycles

Started by HIRTintl

Replies: 3
Views: 957
Last post February 14, 2012, 06:44:59 AM
by jumptrout51
Whirlpool Dishwasher GU1200XTLQ1 Dead, clean light blinks.

Started by barb

Replies: 2
Views: 7312
Last post August 11, 2007, 08:05:47 AM
by barb
Whirlpool dishwasher manual

Started by naes

Replies: 15
Views: 18598
Last post August 06, 2007, 05:26:57 PM
by AJ
Video: Whirlpool Dishwasher - Check for foreign objects in food chopper.

Started by AJ

Replies: 0
Views: 21193
Last post August 08, 2007, 12:43:21 PM
by AJ
Whirlpool Dishwasher Model GU940SCGB3 Door Leak

Started by JimKaran

Replies: 10
Views: 13546
Last post September 13, 2007, 11:39:39 AM
by AJ