Author Topic: KENMORE 417.44152400 won't enter spin cycle  (Read 1967 times)

Offline JS22

  • VIP Member
  • Member Since: Aug 2009
  • Posts: 2
KENMORE 417.44152400 won't enter spin cycle
« on: August 02, 2009, 10:38:15 AM »
This unit is 3 years old. It recently started to not enter the spin cycle. I have purchased a new unit ( brand ) since the failure due to numerous incorrect repair attempts by a local repair shop. So many infact they refused to keep coming out. Said they were losing money. So I am trying to repair to sell the matching set. I have ran the diagnostics in the manual and all is working how it should. In fact it spins like no body's business in diagnostic mode but won't during normal use. The error code is 4-3 as I understand it in the manual. This means control board problem. How can it operate as it should in diagnostic mode but not normal mode? Motor was replaced, door lock is working. Any suggestions? Thanks!

Model 417.44152400

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: KENMORE 417.44152400 won't enter spin cycle
« Reply #1 on: August 02, 2009, 03:42:37 PM »
... Motor was replaced, door lock is working...
how do you know the Door Lock is working ?

Besides the mechanical lock, there are (2) Switches in the Door Lock.

Here's one test:

Lock the Door, unplug Washer from Wall Outlet,
try to open the Door ...

Does it unlock right away, or only after a few minutes ?

FRIGIDAIRE Door Lock Assembly, part number: AP4455026






After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline JS22

  • VIP Member
  • Member Since: Aug 2009
  • Posts: 2
Re: KENMORE 417.44152400 won't enter spin cycle
« Reply #2 on: August 02, 2009, 04:23:43 PM »
At this time I cannot run the simple test as requested as I have taken the machine apart. Motor is out, control box is out and front control plate is off. I was trying to see if any connections were not in place. I can tell you that the machine performs as it should except for the spin cycle, it makes a humming noise from the motor when spin is supposed to take place. As for the door lock, while it is in operation it will not open until it is finished, or until you cancel the operation. I have also performed the diagnostic test in the manual which was taped on the inside of the unit, two of which tested the lock and unlock function. Both worked as the manual stated they should. I could put the machine back together and test again unless the above extra info steers the diagnosis in another direction. Thanks for any help!

 

KENMORE 417.44152400 won't enter spin cycle

Started by Critterhntr

Replies: 14
Views: 6416
Last post October 17, 2009, 01:41:02 PM
by Critterhntr
Kenmore frontloader 417.42142100 shaking when in spin cycle

Started by candoan

Replies: 3
Views: 3737
Last post January 28, 2008, 06:04:40 AM
by candoan
kenmore washer clicking on spin cycle

Started by seek1369

Replies: 8
Views: 7569
Last post January 30, 2009, 08:55:05 PM
by JWWebster
Kenmore 90 Series Washer with Spin Cycle issues

Started by B_con

Replies: 2
Views: 2977
Last post February 28, 2009, 08:27:56 PM
by JWWebster
Kenmore 70 Series Washer - no cold water, weak spin cycle?

Started by Q451990

Replies: 10
Views: 3999
Last post January 28, 2010, 08:31:18 PM
by viking351
Sounds Like Jet Taking Off when Kenmore Front Loader in Spin Cycle (Bearings?)

Started by freddy101

Replies: 7
Views: 2810
Last post February 19, 2010, 04:32:28 AM
by schaffersapplian