Author Topic: Kenmore Washer 417.43142300 - no spin/agitate. replaced speed contrl brd  (Read 6859 times)

Offline dtcaruso

  • VIP Member
  • Member Since: Jul 2009
  • Posts: 3
This is one I can't figure out. On my Kenmore washer -model# 417.43142300, it had no spin or agitate but all other functions worked (Door lock, water draining, final spin light lite). 

Pulled back cover, found the speed control board had a blown fuse, so ordered a new one.  Replaced it: washer now does agitate back/forth but very slowly, BUT it still does not have any final or high speed spin.  Water drains, lock is on, final spin light on.

I'm questioning whether the new speed control board is bad or is the wrong one. 
Looking up the washer model # the speed control board is part # 134149220


However the original one i pulled out of the washer had Frigidaire part# 134285700. I guess the old one is superceded with this new #.

Anyone have any ideas on what to do? Should I get another speed control board?  Anything else that could cause it to do what I described above?

Online MajorApp

  • Technician
  • Member Since: Feb 2008
  • Posts: 555
  • Country: us
 The 417 prefix in the model number means it was made by Frigidaire. Did you try replacing just the fuse on the old board?

Offline dtcaruso

  • VIP Member
  • Member Since: Jul 2009
  • Posts: 3
The new speed control board and the old one I tried replacing both have the same type of fuse-- 1 1/4" 12A 250V ceramic with PigTail leads. The fuse is soldered into the board....So far, I can't find anything that is similiar to those....so, No, have not replaced the fuse yet...still trying...A

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Are you sure all the water is draing out? If not it won't go into high speed spin.
Take the pump off and check for blockage, part # 137108000

Offline dtcaruso

  • VIP Member
  • Member Since: Jul 2009
  • Posts: 3
Removed the pump, checked for blockage--it was clear, impeller in the pump rotates..looked into the down tube from the TUB, it was clear.

Just measured the resistance (per the paperwork inside the washer) of the spin motor. On the 6 Pin plug going to the motor, pins 1, 2, 3 all measure 2.6ohms (1-2, 2-3, 1-3).  So not sure what to do? I'm going to try another spin control board as I can't think of anything else that could be wrong... Ideas??????? HELP!!!!!
ALSO---Thanks for your response!!!!
 

Offline dennisc

  • VIP Member
  • Member Since: Nov 2009
  • Posts: 1
I had the same issue- slow speed on spin. I replaced the board , and it was fine for 1 load. The next load, it went back to a slow spin

 

Kenmore Washer will not drain or spin, agitates on the agitate lo cylce only

Started by mattz

Replies: 5
Views: 9497
Last post March 11, 2008, 09:21:43 AM
by mattz
Kenmore 41744052401 washer - No high speed spin.

Started by ALTANertive

Replies: 2
Views: 3571
Last post February 02, 2009, 09:17:47 PM
by ALTANertive
Kenmore washer won't drain, agitate or spin

Started by dwolfgram

Replies: 7
Views: 7012
Last post May 12, 2009, 02:53:59 PM
by JWWebster
whirlpool washer wont spin or agitate already replaced coupling what else??

Started by crazy7605150

Replies: 10
Views: 5242
Last post October 12, 2009, 10:53:21 PM
by Washaman
110.24934200 Kenmore washer wont agitate or spin

Started by acunningham7513

Replies: 1
Views: 1691
Last post October 30, 2010, 03:41:18 PM
by AJ
Kenmore 70 Series washer won't agitate or spin

Started by fungas

Replies: 12
Views: 12778
Last post August 22, 2011, 02:07:07 PM
by AJ