Author Topic: Matag washer frustration  (Read 10300 times)

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Matag washer frustration
« on: January 18, 2008, 01:50:31 PM »
I have an old Maytag top-load washer (1981, I think). The function on the timer dial does not match what it is actually doing.  Appears not to agitate and when it is time to drain, you hear loud ticking or humming. If you give the washer a good shove, it will then drain. I replaced both belts...no change.

Is it the timer or?????

Can not afford a new washer, unless the repairs are more than the washer.  Need your help big time!  :(

Model A608

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #1 on: January 18, 2008, 06:57:43 PM »
a model number would be helpful
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #2 on: January 18, 2008, 09:29:10 PM »
The model number on the plate on the washer and the one I used to order the belts is A608. I can not read the serial number as it is worn down.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #3 on: January 19, 2008, 07:40:07 AM »
sorry, I didn't recognize that model number.

sounds like it may have multiple problems

The timer may be about $100

I found the wiring diagram...

In another forum, they mentioned that if the water level switch was activated, either by a bad switch, or by water not being completely pumped out, clogged hose, ect, it would keep power to the timer motor and advance to the next cycle.




« Last Edit: January 19, 2008, 09:04:25 AM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #4 on: January 19, 2008, 09:25:13 AM »
Would that make it a switch or a timer problem or both? :D  and would this explain the noises and no agitation?

  Do you know if this model has a reversible motor..one way for agitate and one for spin ..I saw somewhere that the motor could be half burned out so one function would work and not the other.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #5 on: January 19, 2008, 09:47:43 AM »
the reversible motor use the same winding for forward/ reverse.

Does it spin OK, and does it drain during spin, or does it only spin when you "give it a good shove"

Does it make any unusual noise during spin or when trying to agitate ?

After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #6 on: January 19, 2008, 10:10:12 AM »
Now 70% of the time it only spins when I give it a "good shove."  When it should be agitating, and isn't, it makes no sound and the dial moves along but when it should be draining there is that ticking or loud humming noise that eventually stops.

does that help?

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #7 on: January 19, 2008, 01:13:11 PM »
How fast is it ticking ?

Try tapping (closed fist) on the timer. It may help on spin, and maybe on agitate. Otherwise you'd need a volt-meter to make some tests.

After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #8 on: January 19, 2008, 06:59:15 PM »
The ticking is a fast ticking, like a clock and probably is from the timer and it is doing that loud "humming noise" (i can hear it on the main floor with the washer in the basement  ???).

The dial itself is a push/pull function (pull out to start it) so tapping on it doesn't work.

I have a Sear's Analog Multi-tester 18 range, would that work as a volt meter? if you have the patience to explain the testing to me I sure would like to try it.  I do not want to buy a timer and have something else wrong too. I think the dial is stripped and that is why the functions do not line up, but the functions should still work in order.

Thanks for all your help thus far!

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #9 on: January 20, 2008, 12:43:20 PM »
The loud "mmmmmmmmmmmmm" noise is present for all of the functions except fill, and that is all it will do now.(and drain if I shove it)

What/where do i test with the ohm meter so that I can go head and order the parts or give up and call a repair person.

Thanks

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #10 on: January 20, 2008, 01:03:33 PM »
will it agitate if you "give it a shove" (when full of water) ?
or try to reach in carefully and give the tub a start.



« Last Edit: January 20, 2008, 01:22:45 PM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #11 on: January 20, 2008, 01:28:31 PM »
Yes, it will agitate if I give it a "shove" :)

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #12 on: January 20, 2008, 01:38:08 PM »
what about giving the tub a spin carefully to see if that helps the motor start.
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline frisky

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 15
Re: Matag washer frustration
« Reply #13 on: January 20, 2008, 01:49:41 PM »
I held the lid switch in and tried to move the tub, it does not seem to want to move. Closed the lid, shoved it and it started to spin.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Matag washer frustration
« Reply #14 on: January 20, 2008, 01:56:14 PM »
have you tried it on each of the speed settings before starting it ?


continued on page 2
« Last Edit: January 20, 2008, 02:12:10 PM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

 

Matag performa washer died

Started by jbdcamaro

Replies: 4
Views: 1857
Last post July 06, 2009, 05:07:20 PM
by Repair-man
Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 8614
Last post February 09, 2013, 07:41:01 AM
by def
Frigidaire Front Load washer making noise.

Started by curtis

Replies: 3
Views: 7691
Last post July 05, 2007, 09:25:04 PM
by AJ
Repair Guide: Whirlpool Direct Drive Washer - No agitate or spin

Started by AJ

Replies: 13
Views: 28456
Last post January 02, 2009, 01:09:38 PM
by AJ
Noisey Washer

Started by jdman

Replies: 15
Views: 7495
Last post July 28, 2007, 09:51:14 AM
by AJ
Estate washer leaking oil

Started by gearhead

Replies: 1
Views: 5822
Last post July 31, 2007, 06:39:31 AM
by AJ