Author Topic: Kitchenaid KEBC107 Oven No Heat  (Read 8292 times)

Offline thepicker

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 3
Kitchenaid KEBC107 Oven No Heat
« on: January 16, 2008, 07:28:26 AM »
Hi,
 My kitchenaid oven stopped heating. The display just stays on LO.  It happened once before and then just started working after a day or two. The fan, lights, and everything else seems to be working fine.
    I tested the thermostat-thermofuse behind the panel on the back and it was closed(ohm meter showed a circuit).   The two red wires going to the lower heating element had no voltage. It's about a year old and has never been in self-clean mode.   Any advice would be helpful.
   the picker

Model Number: KEBC107KBL0
« Last Edit: January 16, 2008, 11:39:58 AM by AJ »

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kitchenaid KEBC107 Oven No Heat
« Reply #1 on: January 16, 2008, 07:40:00 AM »
what's the letters and numbers after the model number ?

does the BROIL or CONVECTION heat work ?
« Last Edit: January 16, 2008, 07:57:33 AM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline thepicker

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 3
Re: Kitchenaid KEBC107 Oven No Heat
« Reply #2 on: January 16, 2008, 10:47:59 AM »
Hi,
  Thank you for the response. The full model number is KEBC107KLB.  I could not get heat from any mode.  I even tried dehydrate and bread raising modes.
  tom.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kitchenaid KEBC107 Oven No Heat
« Reply #3 on: January 16, 2008, 12:28:47 PM »
I couldn't find KEBC107KLB
 Could it be a KEBC107KBL ?

It could be a bad DOUBLE LINE BREAK RELAY (not on KEBC107KBL0)  on the electronic control board. The relays are not normally replaceable (unless you can solder and find a replacement).


Depending on which model you have:

You could test it by jumpering the CORRECT 2 RED wires on the control board.

The controller is part #4456033
« Last Edit: January 16, 2008, 01:21:49 PM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline thepicker

  • VIP Member
  • Member Since: Jan 2008
  • Posts: 3
Re: Kitchenaid KEBC107 Oven No Heat
« Reply #4 on: January 16, 2008, 03:07:53 PM »
Hi,
 It is KEBC107KBL, my fault.
 Thanks a lot.  Does replacing the control panel  require soldering?
 thepicker

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kitchenaid KEBC107 Oven No Heat
« Reply #5 on: January 16, 2008, 04:00:06 PM »
it shouldn't require soldering, the diagrams show all plug numbers, EXCEPT the (2) red wires to the DOUBLE BREAK RELAY (if equipped).

They may have to be soldered.

It may no longer be used on replacement control board.

compare your board to the pictures of the (newer) replacement board.

If you have one and the replacement doesn't use one, you MAY be able to bypass it.

It may be a safety disconnect incase one of the other heater relays stick. The new board MAY have better heater relays...



« Last Edit: January 16, 2008, 04:07:18 PM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

 

Kitchenaid Double Oven no Heat after Self Clean

Started by TechnicianBrian

Replies: 0
Views: 5432
Last post November 18, 2008, 02:03:23 PM
by TechnicianBrian
Kitchenaid oven controls operate but no heat

Started by mtnbikeman

Replies: 9
Views: 4536
Last post November 24, 2009, 04:15:04 PM
by Repair-man
Kitchenaid Double Oven won't heat

Started by emshields

Replies: 4
Views: 3056
Last post November 07, 2011, 08:57:09 PM
by tgoods
Whirlpool Buit-In Oven - No heat

Started by AJ

Replies: 0
Views: 2850
Last post December 28, 2007, 07:41:25 AM
by AJ
Kitchenaid Range no Oven Lights

Started by TechnicianBrian

Replies: 0
Views: 3286
Last post May 20, 2008, 10:03:36 PM
by TechnicianBrian
Kitchenaid Oven not Heating after Self Cleaning

Started by TechnicianBrian

Replies: 0
Views: 3816
Last post August 27, 2008, 06:46:01 AM
by TechnicianBrian