Author Topic: Kenmore dryer makes a squeak like a hampster wheel.  (Read 6672 times)

Offline justinc25

  • VIP Member
  • Member Since: Apr 2008
  • Posts: 17
Kenmore dryer makes a squeak like a hampster wheel.
« on: June 12, 2009, 07:23:02 PM »
Hi There,

My friends dryer is making a squeak like a hampster wheel when running.
Other than the noise it works fine.
I'm thinking maybe rollers, or belt tensioner wheel ?
Let me know what you guys think. She is low on cash and asked me to look at it.
I'm pretty handy, and have done repairs to my washer before, as well as converting my dryer from natural gas to LP. So I'm confident I can fix this issue.

Thanks,
Justin

Model 417.80042990

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore dryer makes a squeak like a hampster wheel.
« Reply #1 on: June 12, 2009, 07:40:50 PM »
Behind the dryer section of this stack job is an access panel to the idler. Get some zoom spout oil from ace hardware and oil that idler. Their is also a hole in the dead center of the back of the dryer that the static discharge ball attaches from the rear bearing. Sometimes you can put a little zoomoil on that and stop the squel and the zoomoil is heat resistance and non flamable. Just a tad will do it. Let me know.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline justinc25

  • VIP Member
  • Member Since: Apr 2008
  • Posts: 17
Re: Kenmore dryer makes a squeak like a hampster wheel.
« Reply #2 on: September 01, 2009, 03:42:13 PM »
Behind the dryer section of this stack job is an access panel to the idler. Get some zoom spout oil from ace hardware and oil that idler. Their is also a hole in the dead center of the back of the dryer that the static discharge ball attaches from the rear bearing. Sometimes you can put a little zoomoil on that and stop the squel and the zoomoil is heat resistance and non flamable. Just a tad will do it. Let me know.

Finally got over to her house to fix it. Thanks So Much, Your advice was right on !!
A little oil to the hole in the back of the dryer fixed the noise.
I also oiled the idler and the motor, to prevent any other noises. She was worried that it was no good. Only 2 bucks for the oil. THANKS AGAIN !!  ;D

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore dryer makes a squeak like a hampster wheel.
« Reply #3 on: September 01, 2009, 09:53:45 PM »
If it keeps squeaking you needs to replace the bearing or the drum mount will fail.
Dryer Rear Drum Bearing Kit Part # 5303281153
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Sears Kenmore Dryer - Makes Rumbling Noise

Started by AJ

Replies: 0
Views: 4563
Last post January 04, 2008, 05:37:36 PM
by AJ
Kenmore Dryer Discontinued Wheel Blower

Started by Trav13

Replies: 9
Views: 3059
Last post January 23, 2009, 11:03:53 PM
by AJ
Kenmore 4 wheel dryer de-mystified

Started by JWWebster

Replies: 1
Views: 978
Last post November 01, 2011, 12:56:32 AM
by Washaman
Kenmore Dryer

Started by jdman

Replies: 6
Views: 5854
Last post August 12, 2007, 07:30:06 PM
by AJ
Kenmore Electric Dryer - Model F60909644

Started by txgal

Replies: 1
Views: 4148
Last post August 07, 2007, 08:21:33 AM
by AJ
Kenmore 71802 Gas Dryer won't stay hot

Started by Chris

Replies: 3
Views: 5412
Last post August 21, 2007, 07:22:14 PM
by Pegi