Author Topic: Inglis model number  (Read 5969 times)

Offline cse_20

  • VIP Member
  • Member Since: May 2009
  • Posts: 13
Inglis model number
« on: May 25, 2009, 10:38:51 PM »
Hi
I have a old (~20 years) Inglis washer, direct drive, 2 speed SUPERB model.

But I cannot find the model#, serial#.

I have to replace the coupler between the motor shaft and the transmission shaft, but I would also like to get a couple of other parts when I go for parts.

Any ideas where the model# is located?
Regards,
cse_20

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Inglis model number
« Reply #1 on: May 26, 2009, 05:59:08 AM »
On most of the Inglis and the Whirlpool machines the model is just inside the lid area at the rear edge of the main top.
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Re: Inglis model number
« Reply #2 on: May 26, 2009, 08:13:52 AM »
It's pretty hard to track down Inglis parts even if you have the model #. The good news is that the basic parts are the same as any Whirlpool topload direct drive models so it uses the same couplers etc.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Inglis model number
« Reply #3 on: May 26, 2009, 08:38:51 AM »
285753 coupling
80040 dogs
3363394 pump
« Last Edit: May 26, 2009, 08:47:51 AM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline cse_20

  • VIP Member
  • Member Since: May 2009
  • Posts: 13
Re: Inglis model number
« Reply #4 on: May 26, 2009, 10:12:59 AM »
Thanks for the info, I have read that it's a good idea to replace pump if the coupler goes?

I had already changed the "dogs" about 5 years, maybe they are due too.

Plus I need the front feet, apparently they were never installed, always wondered why it was a pain to move, now I know.

Thanks again.
Regards,
cse-20

Offline cse_20

  • VIP Member
  • Member Since: May 2009
  • Posts: 13
Re: Inglis model number
« Reply #5 on: May 26, 2009, 12:56:13 PM »
Repair-Man, you the man!
I finally found the tag, with the lid open, it's just behind.
Being 6'2" I have to get on my knee to see this thing.

Anyway, I picked up the new improved coupler with the metal sleeve, a new water pump, a agitator repair kit which has a couple of the parts I need, and Myrtle should be okay for
a few more years.

Thanks to all for your time and patience.
Regards,
cse_20

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9427
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Inglis model number
« Reply #6 on: May 26, 2009, 02:32:29 PM »
Quote
I finally found the tag, with the lid open, it's just behind.

Could you please post the model number?

Thanks,
Hope you find our site helpful.

Offline cse_20

  • VIP Member
  • Member Since: May 2009
  • Posts: 13
Re: Inglis model number
« Reply #7 on: May 26, 2009, 03:06:59 PM »
Yes sir,

X044100 Type:107

Offline cse_20

  • VIP Member
  • Member Since: May 2009
  • Posts: 13
Re: Inglis model number
« Reply #8 on: May 26, 2009, 10:32:48 PM »
So the washer is up and running again, took awhile I had in pieces literally.

Changed the coupler, changed the pump and the agitator dogs, they were due.

Two little things I'm not happy about though, there is a very minor leak, seems to be on the fill cycle. Like a 2-3 inch wide puddle from the front end.
I'll have to open it up the right way this time and see where and why.

The other problem is I had this on it's side overnight and a cap full of oil from the transmission spilled out from the top vent hole.

Is it possible with maybe a syringe to put some back in?
Regards,
cse_20

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Inglis model number
« Reply #9 on: May 27, 2009, 12:09:41 AM »
Don't worry about the tranny oil. Did you forget to properly clamp the new pump? Been there done that.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline cse_20

  • VIP Member
  • Member Since: May 2009
  • Posts: 13
Re: Inglis model number
« Reply #10 on: May 27, 2009, 08:59:18 AM »
Thanks for the re-assurance for the tranny oil.

I'm pretty sure I clamped up all the hoses, but I'll recheck nonetheless.

Maybe a few cycles with hot water will reset them back to their former snugness ;D
Regards,
cse_20

Offline JLPSullivan

  • VIP Member
  • Member Since: Jun 2014
  • Posts: 1
Re: Inglis model number
« Reply #11 on: June 10, 2014, 09:45:09 PM »
I have a similar machine to this. Its the UO-44501 and there is a knocking while its supposed to be agitating (only active in one direction). Clearly something is broken but when I attempt to remove the retaining nut at the top of the agitator it won't budge off the spindle. Should I apply more force, or is there more to the dismantling that I'm missing?

 

Frigidaire gallery Front loader (unknown Model number)

Started by subnet76

Replies: 6
Views: 1741
Last post January 14, 2012, 11:09:25 PM
by MajorApp
Model #ITW4300XQ0 - Inglis Automatic washer

Started by abdo2008

Replies: 4
Views: 1617
Last post February 16, 2012, 03:10:08 PM
by RegUS_PatOff
Maytag washer, model number #MVWC200XW2

Started by resapp

Replies: 2
Views: 1377
Last post April 14, 2013, 09:49:18 PM
by AJ
Whirlpool Inglis Model # ITW4300SQ0 Leaving oil/grease spots on clothes

Started by Washaman

Replies: 6
Views: 1481
Last post May 22, 2013, 08:47:48 PM
by AJ
Inglis washer model ITW4300XQ0 won't stop filling

Started by brad

Replies: 4
Views: 726
Last post September 16, 2014, 02:01:48 PM
by dab147315
Maytag Washer Model mav7600aww, noisy

Started by dex

Replies: 1
Views: 4821
Last post October 31, 2007, 05:50:56 PM
by rickgburton