Author Topic: Washer Walking on spin cycle  (Read 1430 times)

Offline Lee

  • VIP Member
  • Member Since: May 2009
  • Posts: 10
Washer Walking on spin cycle
« on: May 19, 2009, 11:54:57 AM »
Washer is walking on spin cycle.
Also need advice on how to access washer from front or how to open up front and top panels IE; screw removal, prying,hammering,torching,bulldozing (just kidding)
Thanks,
Lee

Model FWS235RFS6

Offline BrntToast

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 388
  • Mayday Appliance Service
    • frigidaire service blog
Re: Washer Walking on spin cycle
« Reply #1 on: May 20, 2009, 08:39:03 PM »
there are clips that hold the lid down, you insert a putty knife in the gap between lid and front panel and push in on the clips then lift the lid
the front panel has 2 screws near the bottom, remove screws and lift lid, then the front panel slides down and comes off
off balance can be a few things, broken leg on base,broken spring, bad snubber or broken bolt on inner tub trunion

so once front panel is off first thing is a good visual inspection, common friggy problems.... oil leak from trans greeses snubber and causes it to slide too easily,   so look for oil

another i see alot of is the broken bolt on the inner basket trunion... to test this you grasp the top of the inner tub and rock it. the outer tub should move with the inner, if the inner tub moves more or feels loose you need to remove the agitator and check the 2 bolts under there

btw, if it is that bolt broken you can replace it at any hardware shop,  BUT make sure its a galvanised or stainless bolt or it'll rot in no time
« Last Edit: May 20, 2009, 08:42:07 PM by BrntToast »
Mayday Appliance Service
Winnipeg Manitoba Canada


The only stupid question is the one not asked

Offline Lee

  • VIP Member
  • Member Since: May 2009
  • Posts: 10
Re: Washer Walking on spin cycle
« Reply #2 on: May 26, 2009, 11:09:26 AM »
I did get the panels off and looked at all the springs etc and thought there was a bolt missing on the bottom that held the drum in place.So I called the local store and and talked to a tech and he said it was most likely the snubber, like you said, and that it was quite a job to replace.
So that's where I am at,the washer is about 10 years old?.Got any preferences on a front loader?
Lee

 

Washer Walking on spin cycle

Started by Vernald

Replies: 4
Views: 1501
Last post May 20, 2009, 08:38:07 AM
by Mr. Fix-It
washer shaking during the spin cycle and "Walking" during spin cycles also

Started by dnunley

Replies: 6
Views: 2968
Last post February 09, 2011, 06:43:50 AM
by jumptrout51
Maytag washer mah4000aww spin cycle

Started by evo100

Replies: 1
Views: 3273
Last post December 25, 2007, 09:41:02 PM
by AJ
washer works except spin cycle and has a burning rubber smell.

Started by hogslayer

Replies: 4
Views: 4825
Last post February 19, 2008, 03:50:55 PM
by JWWebster
Maytag washer-- got agitation, no spin in spin cycle

Started by PB3

Replies: 13
Views: 12602
Last post March 28, 2008, 09:18:30 AM
by PB3
washer trips gfi at spin cycle

Started by rhartman93643

Replies: 7
Views: 4206
Last post April 18, 2008, 11:57:24 AM
by rhartman93643