Author Topic: whirlpool dryer not getting hot  (Read 2215 times)

Offline janas^883

  • VIP Member
  • Member Since: Apr 2009
  • Posts: 1
whirlpool dryer not getting hot
« on: April 16, 2009, 06:51:08 PM »
Hi i have a dryer that just won't heat. I have tested the heating element with my multimeter, but i don't know how to test the thermostats or fuse. Any help would be greatly appreciated.  

Model Number: LE5530XSW0 icon

Offline Icehouse

  • Technician
  • Member Since: Oct 2008
  • Posts: 569
    • hvacbob
Re: whirlpool dryer not getting hot
« Reply #1 on: April 19, 2009, 12:15:23 PM »
First the power to the machine should be off.
Next remove the wires on the heater element.
Set the meter to "ohms" (#8 on it's side).
Place leads on the element connections that you just removed the wires from.
The reading should go up, if no movement, element is open and needs replacing.
This also applies to the thermostat.  :)
NATE, NCCER, PHCC,HVAC Certified Instructor
Member RSES, US Army Refrigeration Specialist(Retired), Former Refrigeration Teacher NYC Board of Ed.
a tragedy has happen to me : http://web.me.com/zenzoidman/Bobice/

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: whirlpool dryer not getting hot
« Reply #2 on: April 19, 2009, 09:24:26 PM »
Any of the clixons mounted on the back around the heater are subject to be open and that would kill the heater. The most likely dude to blow is mounted on top of the heater chamber. This puppy will die pretty dang quick if the vent pipe is stopped up or kinked and thus not allowing for proper airflow.The replacement part comes with both the limits that mount on the heater chamber. So if the heater is ok then that is where I would start. the clixons on the blower housing judge air temp and the white skinny thang is ok because if it was bad the dryer would not run.
Here is how it works. When you put the dryer in the heat mode and all is kosher. the heating element comes on. The clixon mounted on the blower housing judges the temp of the air. It regulates the heat continuously during the drying cycle. It almost NEVER fails. Next to it is a skinny white fuse that is tied into the door switch. if the lint buildup inside the dryer filter housing blocks the flow this one will melt and kill the power to the motor. The cent switch which carrys the heater load will shut down and kill the heater. if the dryer is running then I would not bother to check that one. On the bottom of the heater chamber is 2 wires going to the heater and just above that is a 250 degree limit. It has a partner in crime above it (smaller) that blows at 300 f. that is the one you will find open 99% of the time. Before you make any attemp to replace the limit be sure you clear out any lint and other obstacles blocking the airflow.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Video: How to check voltage at cord on a Whirlpool electric dryer.

Started by AJ

Replies: 0
Views: 9029
Last post August 06, 2007, 05:57:19 PM
by AJ
Video: How to take your Whirlpool dryer apart to replace parts & remove lint

Started by AJ

Replies: 0
Views: 21383
Last post August 16, 2007, 06:02:43 PM
by AJ
How to replace Whirlpool Dryer Motor.

Started by AJ

Replies: 2
Views: 8191
Last post January 15, 2009, 08:13:09 PM
by AJ
whirlpool dryer gew9250PW1

Started by rclarkco

Replies: 1
Views: 4377
Last post December 16, 2007, 01:17:43 PM
by Pegi
Whirlpool Dryer - Run, but does not heat.

Started by AJ

Replies: 2
Views: 3459
Last post January 10, 2014, 12:26:55 PM
by fairbank56
whirlpool dryer metal on metal sounds?

Started by amnesty

Replies: 5
Views: 5893
Last post May 16, 2009, 01:10:38 PM
by mr_fixit