Author Topic: stop spinning  (Read 3785 times)

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Re: stop spinning
« Reply #10 on: March 22, 2009, 02:02:56 PM »
I would remove it before you order the part because sometimes it's a broken retaining pin that causes this problem.

Offline edmart

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 19
Re: stop spinning
« Reply #11 on: March 22, 2009, 02:06:09 PM »
is this the clutch and clip assembly and is there a local hardware store that carries this part? if its the pin as that something i can get at any store.

Offline edmart

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 19
Re: stop spinning
« Reply #12 on: March 22, 2009, 02:09:24 PM »
do i remove the clip or were can i find instructions on how to remove.

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Re: stop spinning
« Reply #13 on: March 22, 2009, 02:12:15 PM »
The pin you can get at the hardware store but the clutch would have to be bought at a GE dealer. The manual would be in the GE section of this forum.

Offline edmart

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 19
Re: stop spinning
« Reply #14 on: March 22, 2009, 02:13:21 PM »
were is this pin located.

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Re: stop spinning
« Reply #15 on: March 22, 2009, 02:18:22 PM »
You have to remove the clutch from the motor it goes through the shaft the clutch mounts on top of it.

Offline edmart

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 19
Re: stop spinning
« Reply #16 on: March 22, 2009, 02:42:01 PM »
to remove clip do i just prythat off or with a hammer and screw drive hit the back until it popa off

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Re: stop spinning
« Reply #17 on: March 22, 2009, 02:44:34 PM »
You lift the top of it and then pry it off dont damage the shaft or you'll never get the clutch off.

Offline edmart

  • VIP Member
  • Member Since: Feb 2009
  • Posts: 19
Re: stop spinning
« Reply #18 on: March 22, 2009, 02:50:41 PM »
wha do you meen lift the top is this clip located in front were the belt is n the bottom of the shaft, correct? :-\ :-\

Offline Mr. Fix-It

  • Technician
  • Member Since: Jan 2009
  • Posts: 357
Re: stop spinning
« Reply #19 on: March 22, 2009, 02:55:02 PM »
Yes its U shaped with 1 side going over the top of the shaft that side has a little indent that helps keep it in place so you've got to lift it to get it to clear the shaft.

 

ge front loader stop spinning e54 code drive motor fault

Started by skline11

Replies: 6
Views: 3933
Last post April 12, 2009, 01:19:18 PM
by skline11
Sam Sung frontload washer model P801, E6 shows and stop spinning

Started by shillion

Replies: 11
Views: 5257
Last post May 29, 2013, 10:29:47 PM
by crman
Kenmore Elite Top of the Line quit spinning

Started by Bishop

Replies: 11
Views: 8832
Last post September 06, 2007, 05:24:55 PM
by AJ
agitator not spinning

Started by whit

Replies: 2
Views: 2598
Last post October 22, 2007, 06:21:57 PM
by Pegi
Amana Washer - Won't stop filling with water.

Started by AJ

Replies: 0
Views: 3890
Last post January 03, 2008, 08:46:14 PM
by AJ
Maytag performa spinning out!

Started by lowhook

Replies: 39
Views: 17998
Last post July 07, 2009, 11:13:44 PM
by JWWebster