Author Topic: Maytag Neptune MAH4000AWW  (Read 3777 times)

Offline BOB V

  • VIP Member
  • Member Since: Dec 2007
  • Posts: 3
Maytag Neptune MAH4000AWW
« on: December 13, 2007, 10:34:22 PM »
#1 Today I had my washer repaired and it cost $440 to have the wax motor and the control board replaced is that a good deal ?
#2 I still have a little ticking noise while it washes,could that be a flat spot on the belt? or does anyone have any ideas.

Model MAH4000AWW
        
                      

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9590
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Maytag Neptune MAH4000AWW
« Reply #1 on: December 13, 2007, 10:55:43 PM »
Hi,

You could Check Here iconto see if you could had got the parts any cheaper online.

I doubt it's a flat spot on the belt. If anything a bad belt on a neptune will make a squeaky sound as the tub changes direction during the agitation cycle.

Could be the tub bearings starting to go out.
How old is the washer?
Is it noisy during the spin cycle?

Could you post a video clip of the washer making the noise?

Hope you find our website helpful.

Offline BOB V

  • VIP Member
  • Member Since: Dec 2007
  • Posts: 3
Re: Maytag Neptune MAH4000AWW
« Reply #2 on: December 15, 2007, 11:39:21 AM »
the washer is about 10 years old,i guess it has served its purpose.the little clicking is when it turns slow,which i believe is a bearing too,well i think its about time to replace the washer as a suggestion,in your opinion which front loading washer would you recommend.
                 thank you for your response

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9590
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Maytag Neptune MAH4000AWW
« Reply #3 on: December 15, 2007, 05:42:27 PM »
The whirlpool duet washers seem to do a good job of holding up over the years.

Hope you find our website helpful.

Offline BOB V

  • VIP Member
  • Member Since: Dec 2007
  • Posts: 3
Re: Maytag Neptune MAH4000AWW
« Reply #4 on: December 22, 2007, 12:22:41 AM »
Thank You

Merry Christmas and Happy New Year

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9590
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Maytag Neptune MAH4000AWW
« Reply #5 on: December 22, 2007, 06:36:49 AM »
Merry Christmas  :santa_afro:
« Last Edit: December 22, 2007, 07:46:58 AM by AJ »
Hope you find our website helpful.

 

Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 9249
Last post February 09, 2013, 07:41:01 AM
by def
Maytag Neptune MAH4000AWW - No Spin.

Started by larry

Replies: 39
Views: 62988
Last post February 21, 2011, 01:22:14 PM
by bwhelan
Maytag Neptune MAH4000AWW Won't Drain Water / Smell

Started by mightymac

Replies: 22
Views: 25800
Last post February 15, 2013, 04:35:03 PM
by def
Maytag Neptune MAH4000AWW

Started by scubachris

Replies: 5
Views: 3099
Last post December 22, 2007, 10:28:27 PM
by AJ
Maytag Neptune Mah4000aww will not go through cycles or spin...

Started by Mudd222

Replies: 11
Views: 5591
Last post April 23, 2013, 11:14:30 AM
by def
Maytag Neptune MAH4000AWW burning smell during spin cycle.

Started by ksujason

Replies: 15
Views: 19350
Last post September 14, 2008, 11:46:31 PM
by Repair-man