Author Topic: mah2400 door latch reassembly  (Read 6300 times)

Offline odin

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 17
mah2400 door latch reassembly
« on: November 12, 2007, 11:11:49 PM »
The door on my Maytag Model MAH2400AWW compact front-loading washer cracked at the top part of the hinge.  I was happy to find the service manual here on ApplianceJunk (thanks, AJ!) and promptly took the door off, removed the cover, and epoxied the broken bits back into place.

Now that I'm onto reassembly, I realize that I can't figure out how to reassemble the door latch / handle / spring mechanism.  It seems simple enough:

- the metal hook that goes into the washer body
- the handle that moves the metal hook
- the fulcrum the hook / handle revolve around
- the spring that gives the hook and handle tension

Since the fulcrum is just a plastic pin that only has one position, that leaves 3 pieces: handle, spring, and hook.  For the life of I me I can't figure out how those 3 pieces fit together to provide the right tension in the right places.  The service manual does not show how to reassemble these pieces.

Anyone know how to do this?  Pictures of a working assembled latch from various angles would be great, but any suggestions at all are welcomed.



Offline odin

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 17
Re: mah2400 door latch reassembly
« Reply #1 on: November 13, 2007, 11:42:34 AM »

Slept on the problem and figured it out.  When disassembling the door cover, the spring must have popped loose so it wasn't in the original position.  Since this is such a poorly engineered design, I'm sure others will be looking for this answer, so here it is for posterity.

The spring has two ends, what I call the "closed" or "loop" end which has a solid "U" of metal coming out of the spring coil, and an "open" or "leg" end which has two pieces of metal coming out of the coil.

The trick is that the "loop" end of the spring must be stuck through the latch hole on the back of the door so that it is pressed up against the back of the metal hook that latches the door to the washer.  Then the "legs" of the spring stick up to where they can press against the plastic door handle and keep the handle taut.  You will probably have to pull out the pin the spring rotates around in order to put the spring in the proper place.  Once the spring is in position, hold the plastic door handle in place against the door cover and lower the cover onto the door and it should all snap into place.  Voila!  One working door.

Offline AJ

  • Technician
  • Member Since: Jun 2007
  • Posts: 10372
  • Country: us
    • - Appliance Repair
Re: mah2400 door latch reassembly
« Reply #2 on: November 13, 2007, 01:04:24 PM »
That's great!
Glad to hear you got it working.

Thanks for the update..  O0


8182634 Whirlpool Duet Front Load Washer Door Latch/Lock

Started by AJ

Replies: 0
Views: 7493
Last post April 02, 2009, 09:35:17 AM
by AJ
Maytag Neptune, Door Latch issues

Started by Jaytag

Replies: 3
Views: 3277
Last post November 19, 2009, 04:41:38 PM
by Repair-man
door wont latch

Started by mikey217

Replies: 1
Views: 1696
Last post March 23, 2010, 06:19:10 PM
by schaffersapplian
Front-Load Washer Door Lock Latch Replacement - part #131763202

Started by AJ

Replies: 0
Views: 4088
Last post March 22, 2011, 09:01:21 AM
by AJ
Testing Whirlpool Duet Door Lock Latch Hook Switch Assembly

Started by AJ

Replies: 1
Views: 6036
Last post May 11, 2012, 08:02:51 AM
by rickgburton
Maytag MAH3000AWW Door Boot Seal

Started by

Replies: 15
Views: 16421
Last post October 16, 2012, 07:51:53 PM
by bigbuck