Author Topic: washer stopped in the middle of a cycle and won't start again  (Read 15265 times)

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: washer stopped in the middle of a cycle and won't start again
« Reply #20 on: October 29, 2008, 10:12:20 PM »
Might be the water temp switch or it could be the water level switch, It could very well be in the timer. This is a real wam doozy you got going here. Go back to that cherry switch make sure them connections is tight and it is positioned exactly where it should be so that the strike hits it perfectly. That dang switch arm can get out of alignment
« Last Edit: October 29, 2008, 10:25:48 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline tetsuo73

  • VIP Member
  • Member Since: Oct 2008
  • Posts: 11
Re: washer stopped in the middle of a cycle and won't start again
« Reply #21 on: November 02, 2008, 09:00:08 AM »
man what luck.  After 2 weeks I get the damn thing working again.
Problem was a bad black cherry lid switch that I got new. 

I went out and got a voltage sensor.  I put the sensor next to the wire harness when I pull the timer switch to turn the washer on, the voltage sensor went off.  So I know the timer is good.  I than left the timer on, and move the sensor around, the only area that had power is the lid area.  No power near the fill switch or the pressure switch. 

I pull both of the lid switch out and tested them with my multimeter.   It turns out that the new black switch is no good, so I just jump the two wires, one pink and the other orange together with a wire nut and the washer came back to life! O0

I guess just because the part is new, it does not mean it is not DOA.
Thanks for the help!  I was going to call in the Maytag repair guy on Monday if I could not get the thing working this weekend.

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9602
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: washer stopped in the middle of a cycle and won't start again
« Reply #22 on: November 02, 2008, 09:02:18 AM »
Glad to hear you got it repaired.  O0

Thanks for the update.
Hope you find our website helpful.

 

Washer just stopped working all together in the middle of wash cycle.

Started by bnjmnalan

Replies: 4
Views: 5701
Last post June 13, 2012, 07:29:20 PM
by JWWebster
Washer makes fast tapping noise at start of spin cycle

Started by Rubik

Replies: 9
Views: 6015
Last post May 04, 2009, 09:03:24 PM
by JWWebster
washer stopped during wash cycle

Started by gemini

Replies: 1
Views: 2492
Last post February 10, 2010, 02:08:37 PM
by JWWebster
Washer stops mid cycle and then the start button flashes

Started by Jaytag

Replies: 16
Views: 8983
Last post October 26, 2010, 06:30:32 PM
by JWWebster
GE Washer stops right before spin cycle is supposed to start

Started by oldguard

Replies: 5
Views: 4150
Last post May 23, 2011, 09:43:55 AM
by JWWebster
My LG washer wont start after completing full cycle

Started by aldo

Replies: 0
Views: 756
Last post September 28, 2013, 07:32:50 PM
by aldo