Author Topic: Hotpoint BWD12 Selection Knob keeps turning  (Read 4030 times)

Offline mande01

  • VIP Member
  • Member Since: Oct 2008
  • Posts: 1
Hotpoint BWD12 Selection Knob keeps turning
« on: October 21, 2008, 05:30:32 PM »
Hello,

I have a hotpoint washer dryer about 3 years old.
Over the past while when I start a wash cycle, it begins the first stage (water in), then it starts spinning the drum, after a while it stops spinning and then the selection knob just keeps turning.

Thing is, if I take out the contents and reduce the load, the cycle can be restarted and will work.

But now it won't carry any load at all.

Is there a load cell somewhere that I can replace, I've opened it up and cleaned all parts, reset the PC board.

Any help would be really appreciated. Even a drawing of the insides with labels and stuff would be fab!!!

Regards,
Derry

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Hotpoint BWD12 Selection Knob keeps turning
« Reply #1 on: October 21, 2008, 10:30:43 PM »
Derry we have the penguinator as a tech on this page. Hang in there, he will hook you up. I myself ain't familiar with a GE washer dryer combo machine. Sounds facinating though. I want so much to say maybe the belt is bad, that is my first inclination. It makes sense. After all the washer is a dryer too. The load is done altogether by that machine. GE is grappy lately over here across the pond. I am thinking maybe so on your side also.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Hotpoint BWD12 Selection Knob keeps turning
« Reply #2 on: October 22, 2008, 06:05:33 AM »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline Penguin45

  • VIP Member
  • Member Since: Apr 2008
  • Posts: 81
    • www.ukwhitegoods.com
Re: Hotpoint BWD12 Selection Knob keeps turning
« Reply #3 on: October 22, 2008, 03:18:16 PM »
Baumatic is a Merloni machine, not the same as the Hotpoint, I'm afraid.

Key point with the Hotpoint is that when the dial starts clunking round, the start lamp will start flashing in a pattern, ie 1-2-3-4-pause-repeat. This is an error code. Count the flashes and report back.

Poor motor action could be down to worn motor carbon brush gear.

Penguin45.

 

knob removal

Started by tnrunner1950

Replies: 3
Views: 1887
Last post January 29, 2008, 02:13:05 PM
by JWWebster
Broken Timer Control Knob

Started by mcsquizzy

Replies: 2
Views: 1887
Last post October 26, 2008, 08:44:22 PM
by mcsquizzy
Hotpoint WDL520-P (Evo II) Front Load Washer Dryer Combi

Started by Specialist

Replies: 1
Views: 1197
Last post May 27, 2012, 10:34:50 PM
by JWWebster
Hotpoint topload new style piece of crap

Started by JWWebster

Replies: 1
Views: 1049
Last post March 27, 2009, 12:50:34 AM
by JWWebster
Washer timer knob doesn't affect the control

Started by psm321

Replies: 17
Views: 5115
Last post September 07, 2009, 10:51:05 AM
by AJ
GE Profile Washer -- Motor not turning-- No Spin

Started by Bobby D

Replies: 9
Views: 16146
Last post December 07, 2009, 09:08:09 AM
by JWWebster