Whirlpool dishwasher runs great, but door leaks like crazy

[Enter Model or Part Number]

Enter Model or Part Number

Enter Model Number

ApplianceDigest.com

[Aaronbond1973]

Trying to order the correct part and a little confused. I removed all of front "vanity" or trim panels. I find it leaking from the top (just under push buttons), from the bottom (under where the wiring harness plugs in) and if I open the door while its running a ton of water pours out from the front side of the door. I am assuming the entire door seal is bad? When I look up parts I dont really find what appears to be door seals.

I find door parts like latches and covers and then one part for $100.00 called "inner door". I'm thinking I will need to replace the entire inner door. Can someone tell me if that sounds right to them, replacing that entire inner door? Here's the link to the parts page for this model on this website.

http://www.pcappliancerepair.com/text-model-bom.php?list=1&image51.x=61&image51.y=13

Here is an exploded view of the door for reference as well.

http://www.searspartsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?diagramPageId=00002&componentDescription=INNER%20DOOR&documentId=10055622&modelNumber=DU927QWDB1&productCategoryId=0130000&brandId=1198&modelName=UNDERCOUNTER%20DISHWASHER&backToLink=Return%20to%20Sub%20Components%20list

Thanks in advance.

Model Number: DU927QWDB1

[Repair-man]

The door seal is in the TUB view. Item #10 below:




By your description the float cup (#32) is stuck, allowing way too much water to fill the tub bottom. Check it and the little microswitch it rests on down below (#29). The water level in the tub should never be above the top of the heater element if the float is working properly.

[Aaronbond1973]

Any suggestions on how much water looks like too much water? Or how to verify if the float is stuck?

[Repair-man]

The water level in the tub should never be above the top of the heater element if the float is working properly.

Start a cycle and look at the water level after it has filled and begun washing. Real quick  way to tell if the float is stopping the water before it overfills. Sometimes the float cup can become lodged in the switch lever below. Only a visual exam of the float as you lift it manually will determine if it indeed trips the switch as it should. When the float rises up, the water coming in is supposed to stop.

[Aaronbond1973]

ok, water level is well below maybe 2" below heater element, there was some crud on the float, it is moving up and down better, but I dont think it was overflowing that way. As soon as I close the door its a steady stream like peeing (pardon) coming from the bottom, about half that much coming from the top just under the handle area. Again I dont get why (unless it is the door seal) but when i drop the door (even if I just close it for 2 seconds to run) water pours out from the door. I dont mean like inside the door as if the water is above the bottom, I mean like the door has been filled with water. The seal seems to be good as far as tears, rips or hardness but what else could pour water out from everywhere?

Thanks again for any help

[JWWebster]

Got mice?

[Aaronbond1973]

I think I may have figured it out. It disgust me to admit to this, but I'm running a cycle now with no leak. I noticed the majority of water poured out at the upper left of the door when I opened it. I never knew what that grid was but apparently its a vent of some sort. Well it was packed with crap that makes me sick to think my dishes where in there. Anyway clean it all out and I can only think with the junk in there it was somehow letting water by. could that make sense? When I remove the vent cover you can see right through the door.

[Repair-man]

That vent serves 2 purposes...to let the steam out during the dry cycle and to allow air pressures to equalize in the tub during the wash. With the vent blocked the water could pressure up that inner door area and leak. Don't hear about too many vents clogged, that's one suggestion I would not have thought of until after we had done a few other things.  Glad you found it and solved with no parts used.

[Aaronbond1973]

Thanks for everyone's help. This is an awesome service and got me looking in the right direction. It was the vent for sure, ran it twice all the way through and not one drop of water! I guess in 17 years of running perfect I should do some maintenance.

[Amy]

This worked for my dishwasher too!  The left side of the door was leaking.  I took the vent off, cleaned it, and now it has stopped leaking!  yay!  Just wanted to let you know that this must not be too uncommon.

[AJ]

This is an awesome service and got me looking in the right direction.

[AJ]

This worked for my dishwasher too!  The left side of the door was leaking.  I took the vent off, cleaned it, and now it has stopped leaking!  yay!  Just wanted to let you know that this must not be too uncommon.

Glad to hear you got it repaired.

[fixitgrandma]

Cleaning the vent fixed the problem with my old Whirlpool dishwasher. Anyone who ever watched me load the dishwasher teased me about washing the dishes before washing the dishes. Maybe they won't now!  My vent was clogged because I would put jars in the dishwasher to loosen the labels I couldn't peel or soak off the jar.  I guess I wasn't that much of a "good girl"...   Remove those labels folks!

[Mr. Fix-It]

I find vent clogs rather frequently I think it is a hard water issue most of the time it's like the airborne steam is loaded with calcium corbonate and it condenses when it hits the vent. It's the first thing I check when I come across a door leak.

[coulombe100]

You guys rock! 

Our Whirlpool dishwasher was leaking from under the front door but I never thought to check the vent.   And what a trap of disgusting slime it was...ewwwww!    But after scraping out that ungodly slop with a butter knife and pipe cleaner, the leak is gone!    For good measure, I also cleaned out the water float valve as was suggested early in the thread, so maybe that helped too.

Advanced Search