Washer WD-1274FHB Service manual

[a3gus]

Hello,

Do you have idea where I could find the service manual for WD-1274FHB?

Thanks.

[Repair-man]

Is the manual for the WD3274 going to be much different?  Have a look:

 http://appliancejunk.com/forums/index.php?action=downloads;sa=view;id=10

[a3gus]

Unfortunately for WD3274 the motor is different. This model cannot show the foult code SE (sensor error) as mine. I'm trying to find this sensor (Hall sensor) but apparentely is impossible, it's comming with the motor assy.

Any idea for a good supplyer for LG parts?

[RegUS_PatOff]

SENSOR ERROR

• The electric contact between the connectors
(5 pin, male in the Wire Harness and 5 pin female in the Hall Sensor) is
bad or unstable.
ƒ_ Reconnect or repair the contact in the connector
• The connector (6 pin, male, natural) in the Wire Harness is not
connected to the connector (6 pin, female, natural) of PWB
ASSY(Main) or the electric contact of connectors is bad/unstable.
ƒ_ Reconnect or repair the contact in the connector
• The electric contact between the connectors ‘a6 pin, male in the Wire
Harness and 6 pin female in the controller(Main)‘bis bad or unstable.
ƒ_ Reconnect or repair the contact in the connector
• The Wire Harness between Hall Sensor in the MOTOR and PWB
ASSY(Main) is cut(open circuited).
ƒ_ Repair/replace the damaged WIRE HARNESS
• The Hall Sensor is out of order/defective.
ƒ_ Replace the Motor
• The controller(Main) is out of order/defective.
ƒ_ Replace the PWB ASSY(Main)

the Hall Sensor is available ...
Sears U.S. has some LG parts... check Sears CA

Do you know the part number for your Sensor or your Motor ?

I'll be back in a few hours...

[JWWebster]

Seems to me you need to just go around the harness and make sure you have a good connection with no green corosion anywhere.

[RegUS_PatOff]

here's the Info & Manuals for the WD1070 (& WD1270)

WD1070 Info

[Timatae]

Hall sensor is located behind the stator. Have to remove panel from back of unit, use a 17 mm wrench to remove the stator, Then using a 10 mm to loosen up bolts to remove the motor which the hall sensor is connected to it. It only has a clip that holds it in place. Common part that goes bad from people using too much soap    Hope this helps!  Lg recommends using only 2 tablespoons of detergent as well as softener..

[a3gus]

I have checked with two spare parts suppliers, the Hall Sensor is not available alone. It's comming with the motor assy.
The motor part no. is WMD-300C2 (110V)
The Hall Sensor part no. is SB 040302 (i'm not sure, that's the number writen on the part) see picture attached.

[JWWebster]

Reggie posted this with his list of failure codes " The Hall Sensor is out of order/defective. ƒ_ Replace the Motor" So that there tells you the motor needs to be replaced with that sensor as one item unless Gus knows something we don't know. Do they have an after market part Gus?(aka a3gus)

[a3gus]

I don't know if they have an after market part. But I find it very strange that LG forces me to buy an expensive motor assy for a cheap piece of plastic which is broken (the hall sensor).
Why the f..k they made this piece detachable if there is no way to buy it by itself??

[JWWebster]

Is their any way to glue that sucker back in place I wonder?

[a3gus]

I have repaired my washer machine... it was the Hall Sensor... I had to buy the entire motor assy for that.

[JWWebster]

Glad you got it fixed. If I wanted to buy one of those machines would you recommend it?

[a3gus]

well... my answer is no because of LG... difficulty to find parts.

[tonywong]

I have checked with two spare parts suppliers, the Hall Sensor is not available alone. It's comming with the motor assy.
The motor part no. is WMD-300C2 (110V)
The Hall Sensor part no. is SB 040302 (i'm not sure, that's the number writen on the part) see picture attached.

Funny thing is that I have exactly the same model as you do and with the same error code. How much and where did you pick up the replacement motor from?

The local repair shop that LG recommended came by for $70 only to open up the back and tell me they want to replace both the logic board and the motor for $500+.