Author Topic: Whirlpool duet stream  (Read 23266 times)

Offline misswings777

  • VIP Member
  • Member Since: Sep 2008
  • Posts: 10
Re: Whirlpool duet stream
« Reply #20 on: October 02, 2008, 12:43:30 PM »
Good news!!!!!!!!

Yesterday I received a phone call from the repairman asking if he could come to the house and check my washer out!!!

Well!!!!!!!!!

The good news is there was no mess under the washer when the repair person took the front off the washer!

The best news is there was a replacement part in a nearby city and I may have my washer fixed completely hopefully by Friday.. 

They are however going to use another part number, another washer like mine uses something called 9600 part and they seem to be interchangeable. 

I will ask the repairman and get all the info..

Thank you all very, very much for all your input! O0



Offline misswings777

  • VIP Member
  • Member Since: Sep 2008
  • Posts: 10
Re: Whirlpool duet stream
« Reply #21 on: October 04, 2008, 04:21:18 PM »
Hello All!!
Thank you very much for all the input on my washer!
They replaced the pressure switch today and i am up
and running a load now!!!!!!!!!!!!!!!!!
The pressure switch that works in the 9600 will work in the 9500,
so that is what i have.. Thank you all again for the help!
Signing off as i am up and running now... RJS, misswings777 O0


Offline WFO

  • VIP Member
  • Member Since: May 2011
  • Posts: 1
Re: Whirlpool duet stream
« Reply #22 on: May 20, 2011, 03:46:49 PM »
After spending 6 hours trying to figure out how to get around/bypass the switch....I took the part out to my shop and blew compressed air into the part. Then came back in and it worked once. I disconnected the hose (black on mine) from the lower part of the washer tub and blew in it a couple of times. (rather hard) The washer has now started working like normal again. How long,.....who knows.
Also, the 9500/9600 part are exactly the same part # according to Whirlpool. Also, there was a nice little diagnostic sheet inside the washer in a little plastic bag, (taped to the sidewall) that showed all the codes and some very simple diagnostics anyone could do to troubleshoot the machine.

David

Offline appltech

  • Technician
  • Member Since: Feb 2013
  • Posts: 42
  • Country: us
    • Appliance Technology
Re: Whirlpool duet stream
« Reply #23 on: September 19, 2013, 08:52:37 PM »
I know this is an old topic. But...Has anyone had any other issues other than the pressure switch? Has it ever been the steam board at fault? From what I got from the wiring diagram, there is a triac in the steam board to control the steam valve. Tested voltage leaving the board, going to the steam valve, I found an open neutral(120V to chassis ground). Why would the triac switch the neutral side???

 

Photos: Whirlpool Duet washer with bad bearings, only 2.5 years old!

Started by AJ

Replies: 21
Views: 33787
Last post May 23, 2013, 08:22:19 PM
by Rick32k
Video: Whirlpool Duet Front Load Washer Water Pump Clean Out.

Started by AJ

Replies: 0
Views: 7401
Last post November 28, 2007, 09:58:47 PM
by AJ
How to replace a Whirlpool Duet washer bellow tub door seal

Started by AJ

Replies: 39
Views: 76204
Last post December 24, 2013, 12:16:46 AM
by GB-NC
Whirlpool Duet Sport Error f-01

Started by Ology

Replies: 2
Views: 7867
Last post March 10, 2008, 05:20:36 PM
by Repair-man
Whirlpool duet sport keeps on pumping

Started by hinkelberry

Replies: 3
Views: 1921
Last post March 10, 2008, 10:05:03 PM
by apptech
Whirlpool Duet Washer - F-30 error code and clunking noise in detergent area.

Started by AJ

Replies: 3
Views: 14810
Last post November 15, 2009, 09:34:58 AM
by AJ