Author Topic: maytag Neptune  (Read 2419 times)

Offline malachitejewel

  • VIP Member
  • Member Since: Aug 2008
  • Posts: 1
maytag Neptune
« on: August 18, 2008, 09:39:28 AM »
Well having fun with the control board.  Replaced it once to have it blow again.  The part that blows is Q6.  I have voltage tested the wax latch motor it is at 16 v.  Manual is listed at 24.  Also tested ohms on wax motor it is at 1100 instead of 1900.  Not sure if it is the wax motor or what Q6 is wired too. Help?

Model MAW4000AWW

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: maytag Neptune
« Reply #1 on: August 18, 2008, 10:37:41 AM »
The wax motor runs on 120 volts.

Only the spin enable switch in the lock assembly carries 24 volts.

Replace the wax motor and the board. Replacing individual components on the board as suggested by other web sources is a lesson in futility.
« Last Edit: August 18, 2008, 10:41:41 AM by Repair-man »
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9607
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: maytag Neptune
« Reply #2 on: August 18, 2008, 12:46:23 PM »
Hi,

Something does not seem correct with your model number.

Are you sure it's not a MAH4000AWWicon?

Here are the parts that Repair-man talked about for that model number.

Control Boardicon
Wax Motoricon

Hope you find our website helpful.

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: maytag Neptune
« Reply #3 on: August 18, 2008, 01:50:06 PM »
Was the original Wax Motor ever replaced when the Board was replaced ?

The new Wax Motors have a black plunger.
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: maytag Neptune
« Reply #4 on: August 19, 2008, 11:41:27 AM »
when the wax motor blows it burns out the resisters in the board. If you fail to replace the wax motor then every board you put on there is gonna blow. The way I understand it is when the wax motor is good it locks the lid. When it goes bad instead of it preventing power to the board it bleeds voltage to that board, frying it. When it goes out then it allows full fledged 120 volts to go into the board and frys it.This is a defect . Later models have been modified with better wax motors. They have a different color to show the modified version.
« Last Edit: August 19, 2008, 11:48:20 AM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

 

Maytag Neptune washer MAH4000AWW

Started by Sue

Replies: 8
Views: 9302
Last post February 09, 2013, 07:41:01 AM
by def
Maytag Neptune MAH4000AWW - No Spin.

Started by larry

Replies: 39
Views: 63088
Last post February 21, 2011, 01:22:14 PM
by bwhelan
Maytag Neptune MAH3000AWW Serial 19103060UB

Started by LarryC

Replies: 9
Views: 8281
Last post September 29, 2007, 09:49:12 PM
by AJ
Maytag Neptune MAH4000AWW Won't Drain Water / Smell

Started by mightymac

Replies: 22
Views: 25859
Last post February 15, 2013, 04:35:03 PM
by def
Maytag Neptune will not shut off.

Started by Boatsrule

Replies: 12
Views: 5698
Last post November 02, 2007, 10:15:35 PM
by sparky823
Maytag Neptune MAH4000AWW

Started by BOB V

Replies: 5
Views: 3790
Last post December 22, 2007, 06:36:49 AM
by AJ